Leaderboard

the red looks really good in the sun. i don't think its too black, in fact i think its just right so thats that sorted. Rosso red it is. 2015-12-13_12-41-44 by sheepers, on Flickr 2015-12-13_12-41-53 by sheepers, on Flickr 2015-12-13_12-41-30 by sheepers, on Flickr

Also picked these up from the sand blaster today and dropped to powdercoater.

So got on to work on this today, I suspected the fuel pump was not doing its job. After googling around I learnt there is a jumper in the engine bay to turn the fuel pump on, I jumped this and listened out for it and heard nothing. I found the connector for it where the fuel sender is and checked for voltage, all ok. Lastly I took the top fuel hose off the fuel filter and attempted to make a petrol waterfall, and there was none. Emailing around all the wreckers now to try and find something before end of year! The bummer about it being the fuel pump is that on this car you have to remove the petrol tank to get to the pump, dangit! I sprayed a bit of ether down the throttle and it coughed and revved for a moment so hopefully that means there isn't anything else wrong. anywho heres a picture of the engine because no one likes a picless update

Sunday after Drag Day I set the tappets, installed the clutch and swung the engine back in the hole Hellloooww Strill have to get teh gear box in - Do you even lift Bro? Friends? -+-+-+- Just hefted the gear box in, went pretty well with a jack and two small furniture trolleys, and all my socket extensions, just the fiddly bits like linkages and stuff to hook up now. So thats the front 2/3rds of the running gear sorted, and half the rust. Just brakes, diff, and the rest of the rust to go, but that means chopping up the parts wagon, which means having a running van to store and move the bits which means rust repairs on the van, which ill do over the christmas break ahhhg bloody cars.

The Line up

update time. Had to fix a heap of small problem with the doner panel just small fiddly stuff like this. where the ends were spot welded down. a tiny bit of rust and a bit of damage from taking it off the old car. did as much as I could before getting the inner and out vent panels sandblasted. I damaged three of these, wasn't as bad as I thought to fix. I also welded up the drill hole in the window frame, as I still have the spot welder i thought it will make a nicer job than big old plug welds, i was right. bit of a close up, only just see one spot weld on the side there. everything seems to line up! So I started welding it all in place, scary! not finished yet, should be done this week. getting there! that's the last of the rust in the shell done!

Once upon a misty evening....

Got this back on Friday.... Ran out of gas 100m down the road hahah Cheers Highlux for being the saviour Days off work are Sunday and Monday so got some trim on yesterday morning before some commitments in the afternoon Am very stoked on how it came out Has developed a fuel problem so will check everything is all good in the metering unit tomorrow night, spent two hours today with the old guru on pi stuff here in Tauranga today has told me what to look for and sorted me out for parts with a troubleshooting book he put together so hopefully get that done tomorrow and put the rest of the trim on If we get it done tomorrow with minimal costs involved will be ordering coilover parts this week tooooooooo, very excite Plus roofrack is being built this week ready to put on the car on sunday we decided on something along the lines of this made out of stainless that fits in the existing holes from the last roof racks

Heres Pics of the new one: and home at last It does have the 4th minilite style wheel in the boot =)

event updated. I have even tried a facebook invite this month so we will see how that goes

I bought an absolute humdinger of a gift off the Tard for this just now. Someone's gonna be either stoked or disgusted,

Lol, street cars dont need dyno work, you can easily achieve a safe 95% tune just by hooning around and using a scientific approach to your tuning method, not only that but it is fun. Don't even get me started on some of the dodgy tunes that have come from reputable dyno shops, basically doing it yourself is better most of the time.

well picked up my new project yesterday needs a bit of work but nowhere as much as my old ponty drained the fuel tank out today cleaned the carb and started it up then snap the dizy bearing seized snapped the bottom off my dizy in the oil pump lol never mind more things to fix if anyone has some 318 v8 parts let me know thanks ill up load more pics later

OS drag day was yesterday, and it was a friggen blast! My wideband shit itself before I finished tuning the staged injection, so bought an upgraded sensor that should last a bit longer (Bosch 4.9 instead of Bosch 4.2) Then had one or two nights to try dial in the fuel for the staged injection and make sure it's all fine. In desperation to be faster than last time, yanked out the passenger and rear seats as well as the belts, and made sure to start the day with a near empty tank of gas to be as light as possible. Unfortunately however throughout the whole day I just couldnt get a clean run off the line at all. The motor was running awesomely, I was ~10kph faster trap speeds than previous, but my best time was still half a second slower haha. (14.8 ) I tried a few tricks to remedy the situation... Turned on launch control and set it at various rpm points, didnt really help. Took a bit of fiddling to get the launch control activation working how I wanted, as sometimes it was coming on while I was trying to do a burnout haha. I was doing 3rd gear burnouts without trouble all day, tried for fourth.... baaaaddd idea haha. Ended up doing a gigantic clutch burnout which stunk out my car for the rest of the day haha. woops. I also Setup an E-throttle map that would limit the throttle body to only opening half way in first gear. Didnt help much. Also tried filling up the gask tank right to the brim, to see if more weight over the rear would help. But I just got slower and slower through the day haha. I guess it's one of those things where you cant fix a physical problem (I need traction brackets!) with electrickery. So I was a bit dissapointed with my times, but I was happy to get a trap speed that indicates its worthy of high 13s if it can get a good launch. Still had a frigging awesome day though, its so cool when you have a really close run against someone. I had a camera setup in the car but the axle tramp was so bad that it was shutting off the camera haha! But here's some footage that survived.

Nah bro, this is a bomb!

So now another crown has found its way into the shed. A 1969 Toyota Crown MS53 wags.last registered in 1996 and possibly the last time it ran.This came from the same place as HORNDOG's MS51 coupe.It has been sitting in a shed for quite awhile which has kept it in not to bad condition but the bottom of everything has rusted away, ie doors,sills,guards and tailgate.Tailgate has the worst of the rust but nothing that carnt be fixed.The car is 98% complete all chrome is there and is in relatively good nick .Just missing both front headlight bezels,'custom' badges and rear crown badges.Interior is all there ,factory black ,front seats are buckets with the usual wear and tear.Dash pad has a large bubble in it and the rear dickie seat works.So i trailered the old girl back home behind the 60series cruiser only for it to have a melt down on the way home. The alternator ratted loose and it spat some coolant out of somewere but no split hoses.After a helping hand from a local she was fixed and made it back with out any extra issues. Specs: reg on hold!!! factory 2M replaced with a 4M-U factory 4spd manual on the floor disc brake up front 5 seater with a 2 seater dickie seat in the rear electric tailgate window that still goes,and would go better than most 90s cars windows boot full of crown parts for ms60s 1973-1974 Got her home,chucked in a battery,checked the electric window to see if it still goes and score it works!!!!! Cleaned all the ignition system changed the seized carb over for another and put some gas in her and she fired up purring nicely,just some timing and tappets to adjust.Clutch needs bleeding to see if i can get it rolling under its own power,brakes also need some attention. So no real plans for this as of yet,just get it to drive and stop.Wouldnt mind taking it to the Rangiora car show at the start of the year.The ms65 will be finished first before the wags gets some love This is the parts container that is full of mostly crown 60series crown parts (theres a little left but i took most of it) a few rt80 corona bits,rx30 cressida parts,datsun 260c towbar,taillights and gasket set.these are all for sale and need to go Discuss here-----> //oldschool.co.nz/index.php?/topic/51148-toymotas-1969-ms53-crown-wags-discussion/

the thing I like the most about this is that its in the main project thread trololololololol /good jerb, miss my GT liftback

Good amount of interest from fb

Been pretty quiet on the MX5 front for a number of reasons... I got sick of looking around for a 2nd hand window winder mech, the main issue being that 95% of mx5's seem to be electric, anyway turns out new genuine was not totally stupid price so boom.. also got the sheet of 3mm abrasion resistant polycarb home in one piece thankfully because that shit ain't cheap.

Yes keep being a nerd, it's great.

you say that (and you are probably right) but how cool is what he has achieved with what he has available in both practical and i-t skill and some kiwi ingenuity ? higher trap speed says his method is working and no amount of dyno time would solve his traction issues anyway . also pretty rare and very cool for him to document both his successes an failures as honestly as he does (most dyno shops dont do that either) disclaimer; I have never met Roman and personaly I prefer points , condensors and carbs

I'm sure you can find something... You know you're going to get rubbish in return right? Might even be better, more useful rubbish than the stuff you already own (and I know you own plenty!)

Poor form Go trawl some bins/zebra/junk shops

Finally got around to taking off the passenger door. Not as easy as undoing 4 bolts, hinges are welded on. Had to use a special tool to punch out the 2 pins and separate the hinges. Stripped and sanded back the door frame area, the side of guard where it attaches to the guard and inside of the door. The passenger guard was a replacement and put on when the van was painted orange so absolutely rust free around this area (Bonus). Primed the door outside because it was a hot day. Dried up really quick, easy to spray. But then when i sprayed the van door jam area i forgot to tell myself this wasn't going to dry as quick and ended up with a sag on top. Shit happens

last pic with the tan team, matts 60 series cruiser with his new ms53 crown wagon behide and my 1980 ae70 sprinter sedan next to it

Hey guys does this sound OK? http://www.hurunui.govt.nz/services/community-facilities/camping-grounds-2/amberley-beach-camping-ground/ $5 a night no advance booking req?

Also made some hoses for the radiator.

Few more pics, Had to redesign the remote after the first run, Originally it was designed to be in the off position at 6oclock ,standby at 9, throttle from 9 to 4, but I kept accidentally shutting the engine off when throttling down. So I added a 2nd switch, the top switch is power and bottom one is standby/ run so the throttle is now adjustable on for the entire range of the rotary knob, all I need to to to shut down normally is turn the throttle to minimum and throw the4 bottom switch to standby which lets it stay powered for the cooling cycle. Here's a couple of pics of the unit on it's own, it's designed to be added to any healing cruiser and just uses the seat bolt to attach. and the final touch, the tank stickers ,thanks to Bangbug for printing these off last minute.

had a few spare hours today...

Started making the exhaust...

Hey Clint, Is there any minimum requirement for the brake line heat shielding? i.e does it need to be actual heat shield material with an insulate layer sandwiched between ally/stainless, or will plain old sheet suffice?

Oh i was meaning for PI tanks GreenTC, the Pi sedans have a different tank to carbed sedans, and wagons are obviously different again. My fuel gauge is surprisingly accurate, but when its out, its out. shitty fuel light flickers from quater of a tank down though

Yes thats me Sorry I was not there for sunday, definitely keep it on the calendar for the next one.

Unsure if Ned was talking to me but my comment was firmly tongue in cheek / no such thing as old junk, it's all useful. My biggest problem is going to deciding what to bring. Maybe I'll bring a few things so everyone can play

it has a huge japanese computer on the dash that talks for about 5 mins everytime you start it

So! I recieved a package from the land of 'J': . Which turned out to be these: Foamers gon foam. And picked reyumz up : Look pretty good tbh

Pulled the block off, will probably end up diving in deeper as the kick start shaft is a little shredded. Not bad condition for 43 years of effort from the old girl.

as alluded to in daves post, you need the external regulator from the b1600 your old one just had lamp, sense and battery terminals as it had a internal regulater likely/imo etc

Neither, I only have useful stuff / stuff I might need it one day

Looks like it is getting there.

New neck tube lathed up out of some hollow bar. Jig almost done, ran out of CO2 to do the steering neck part. Seems square enough...

I believe I spotted you driving past my work in brightwater. Thursday arvo I think?

I've been putting aside some surprise gifts in anticipation for this. Hope everybody else has too. Get them wrapped, in whatever you have laying around and bring them down next Wednesday. Wrap it up like fush and chups puhuhuhu

I finally found some time to make some bench seats and get it all home. We had 20 people sitting at it for lunch on Saturday. It was awesome

Weigh in time Loaded on the trailer ready for part 1 inspection for the cert

I haven't been posting her for ages been busy but the two wheeled pine has been going strong! My dads bike when we got it And after