Leaderboard

so after a road test revealed a few things. ive lost alot of steering lock due to the wheel touching the inner lip on the gaurd. i will be getting a metal expert to roll the lip on the front gaurds. the rear only rubs on extreme angles but hasn't on a bumpy highway drive. in terms of steering lock it means i can only go around big roundabouts but it scrapes haha so now that it means i go round the block than around the roundabout i may do down to a 235 width tyre but will wait until the gaurd is rolled. a couple of days after picking up from the trans shop i did a bolt check and a wash and went for a drive. went to whakatane for some mainies and back the next day you will notice the car is still a tad higher in the front than rear. its not so noticable in person unless looking so will keep it this way. quite stoked with the colour and fitment combo. first trip in this involved someone at the gas station coming for a perv at the wheels and asked a few questions about them. also vehicle handles a huge amount better now less of a boat feel. gave me a huge amount more confidence in driving it around corners too. but should really upgrade the rear shocks to something stiffer and a good wheel alignment too yes you can tell me now how ive ruined my barry car

so because i told you i would fill you in with the progress i will. This would have to be the highlight of doing this old girl up and being able to use it. from getting this car back home i was never really happy with how the car sit or how the wheels didn't fill the guards but the priority was to get it legal and drive it. but liked the style of the car and wheel combo. hummed and ahhed for abit and a work friend had a contact that did mag wheels so contacted him and told him what i wanted. wanted to keep the same wheel centre caps i had but after doing some measurements i was shit out of luck. did a quick measure on the car to what wheels were available. and paid and waited two months for them to turn up. Ended up with specialty wheel smoothie in a 15x8 all round in primer. I got these through BG Marketing and got this brand over a cragar because the centre cap quality is better and i could get them in primer. special order from the US with a 7.5 inch baby moon cap now to pick a colour right. black or chrome is fine. Nah go away barry im here to not be like you. this was the hard part of the wheels i had a few colours in mind but the car being orange made it abit more difficult. so after i cleaned up a old wheel and primed it i went to the paint shop for a colour sample. asked for a colour chart to look from. couldn't find something that stood out. old indian joker says he will mix something up so calls me outside to take a look at the colour and gets it bang on first time. buy that and give it a spray. Note Don't put too much filler primer on a wheel because it cracks how about cream right this photo also shows where i had previously painted and blended it in. Unfortunately i liked the colour but just didn't suit the orange of the car. seemed too light for me so i went back to the paint shop and had the colour changed after going to bunnings and mitre 10 and going through the colour charts on a sunday. sprayed the modified colour on Found this colour was more like salmon not what i was after. so found something lying around in the shed in a different colour i liked. slept on it and went back to the paint shop with another colour to be matched. so they made me a small sample and i gave that a test spray and fitted to the car. Hmm brown you say.. so had some more mixed to paint the wheels and figured if i didn't like it ill just paint them black and be done with it. so figured ive got some nice new wheels how will i paint them nicely. figured its not easy on the ground and had an old hub lying around in funny enough the same stud pattern. so welded the hub to a steel stand And i happen to have two hubs so meant i could weld two at a time choice so a splash of this colour over all 4 wheels then gave them a shot of clear coat. couple of ugly bits but nothing much noticeable and wheels can be tricky to get all the paint into spots test fitted the wheels revealed the enviable. cut cut the front was never level with the rest of the car so this had to be done. plus it wasn't low enough painted the cut bit and put them back in for a level test. level looked good would be nice if it was much lower but the car has to be able to be driveable or get in the driveway which involved a 45 degree entry on the old wheels for tyres i purchased some vitour galaxy 245/60/15s from sta parts. i was lucky enough a good mate had a tyre machine and fitted them for me on a sunday. will balance them if they need them but currently they are good. so after the wheels were fitted i washed it and left it outside for the night where i got it towed to go back to the trans shop the next day. unfortunately i got it back 3 months later. upon me driving away he did say the wheel did scrape oops haha lets find out for myself. And if you wanted to know the colour lion brown mate makes for good beer battered fish

Sitting outside cafe this morning nomming down a cake and coffee, watching some barrie in the carpark looking all over my imp, hands on hips, shaking his head and tut tutting. He heads over to the cafe and orders a coffee. Works out that it's me who owns the imp and asks, in a very strong Yorkshire accent, "how long have you had the imp?" "oh maybe 3 years? I rescued it from a rusty shell in a field" I tell him, thinking to myself this could be a nice interesting conversation but having a feeling its going to be painful.. "has it still got the original engine?".. he spits out, no interest shown at all in the fact I've taken the effort to rescue a nice little classic car and done a not too bad a job at it. "nah.. Ive fitted a Datsun engine in there" I replied. Here we go, this will go one way or the other I thought. Fuck me did he roll his eyes and gave me the dirtiest look. He might as well have walked over and thumped me one with the fists i could picture him building in his fit of barry rage. The conversation stopped there and we left, hannah laughing her arse off at how I've gone and upset another barry with my choice of engine

Had a shit as sleep so today was a proper mission. spine of both quarters is welded and ground, didn’t move too much with the tig. this is drivers side behind the end cap above tail lamp Progress shot. rear parcel tray, tulip panel and window corners being gutted out. brother fanged out a new piece for parcel tray dropdown.. it rotted as the piece above rusted. he also made that bit which is a C section same profile (not pictured) here’s a throwback reminder. I fluffed around with the corners, pretty crazy shapes involved and 3 layers.

I got to alex about 4:30 and brother had spent most of the day on it so I snapped some pics quickly one side zipped up and quarter being welded on, other side not far behind!

Here is a trick that others might want to use. VT-VY commodores have a good throttle cable that can be easily adapted to fit almost any car. I have one in my Valiant and now also in the Sigma. They are dirt cheap, a decent length and are available from any Pick-a-Part in NZ. You simply make three plates to clamp the cable at the firewall (with fastening holes to suit your particular car) and if required do a little trimming of plastic and it works a treat.

I've been working away on cleaning the interior up while I wait for my rust dude to free up. The tan interior was bombed with a black spray can. A good way to strip the paint without damaging anything is brake fluid. Takes a a little patience but works. Also, got a sweet new steering wheel. Couple before and afters...

Redesigned the manifold to be a little bit stronger, better clearance on some areas, and easier to wrap with carbon with some bigger radius on things. Ahh and flips the throttles the other way up. Then it took about 3 days to print, had a bit of warping that needed fixing but turned out okay. Test fits good Take some space age materials and smoosh it on there like a cave man: Then trim it up and sand the mounting faces on a piece of glass with some 220 grit. Nearly good to go, still some sharp edges to take care of with the dremel. Carbon splinters are nasty! Also I'm making a new loom because I had managed to create independent disasters on both sides of the firewall. Tried to get the heater box out and had to pull bloody everything out to get it! But now it's gonna be much easier to make a nice loom. Will be good practice for some better projects later, this loom is nice and simple because there's not too much going on. Aircon stuff is about 10kg worth of junk.

Sorted.

Seems the tan interiors are a lot harder to come by than the grey. It didn't come with any door cars, initially I thought I'd find some easy but turns out these are beginning to be hard to find parts for, especially interior parts. Most are thrashed. But I came up on some door cards, rear seat cards and a bunch of other stuff. Stoked! A little grubby but will clean up ok.

Today class we shall be discussing 'project creep'...

Pre-empt that shit and say "no, I had to put something good in it, you know, reliable, doesn't leak like all those useless union made British engines, so I went with something Japanese, precision engineered and trustworthy. Fuck the English, if it was so great there we wouldn't be here, am I right?"

Found underneath the black paint some of the original Sebring Red paint. This is quite a cool coincidence, as this is a Capri fuel tank and the colour the car will be painted in.

Round two Cleaned up the old sill a bit more so I could check what I was doing. Cur the step into the lower form and clamped that down too Worked out better. I'll extend the press tool a bit more and hopefully get less of a crease for round 3. Also got the other one back from the painters after a month in paint shop / covid jail. The damage to the roof from the roof rack has been fixed up nicely.

He'd be even more horrified to learn what's going to be in it.

Put the 2" blocks in, rolled the rear guards and fitted the rear pair of brx Never before seen footage of the crusty tailgate. Looks a lot worse than it is due some usefull person touching the whole tailgate up with paint applied with a brush

Me and a mate built this at Uni as part of the design stuff for a competition, we didn't actually win on the day due to the way the results were calculated but we went twice as far as any other entry and i think they still use it as an example... Firstly, this is how it works, the basic setup. The red is a bit of 5mm polyurethane, all else is aluminium; Then you pump air in which seals the barrel and fills the outer. Once it is pressurised you remove the pump, the valve actually has nothing in it so the removal acts as the trigger; When the valve is removed the pressure on the polyurethane seals the valve/inlet and all the air rushes out, pushing whatever is in the barrel with it. And as promised, a video of it in action and some fucking dodgy editing for lols.

Is that like stranger danger

Might have to give ya fancy snap on box a squirt in the colour so it matches bro haha

Yeah mate original Austin made A series.

I know, stupid ecu's. I told her if this was a Triumph Herald it still wouldn't be going - but at least I would know why.

Blardy modern cars. grumble grumble. Slap an SU on it and call it done.

So while i had the trans out as i couldn't use the car i decided to tackle some rust the car had. My wof inspector had mentioned it a few times and thought i better fix it after him being nice and giving it two prior wofs as it was. 2nd inspection i put some insolation tape over the holes after i had poked around with a screwdriver haha. I was also lucky that this rust was never noticed while the car was complied or had the repair cert done. I knew it was there but kept my mouth shut. Ah no bondo bob has been in here. I cleaned up the bottom pieces with a portable sandblaster and applied a few layers of crc zinc it well that would be why its rusty. full of dust and dirt that at some point has been wet or had moisture in it. also cut a piece out of the inner wheel well. i had previously when the car had been blasted and painted of the underside i applied a small layer of bog over the pinholes and blended it back in with black paint. I firstly made the curved bit to keep a guide of the shape and location and welded that in. I then cut the outer piece out and made a replacement. This piece was made with 5 different bits all welded into one patch. Also made a new piece for here with 2 bits and curving it to suit the wheel well shape. Then applied a small layer of bog to keep it looking nice. sanded and painted area black to hide all the sins. Then i became bondo bobs brother The reason why this got bogged back up is because at some point the car has had a hit in the passengers rear quarter one big enough that had required the chassis to be repaired when i got the car. im not keen on removing the rear quarter of the car to get the body lines good as the rest of the car isn't that perfect either. So body filler was used to get the door and quarter lines looking good. Sanding and shaping the bog actually took me more time than the metalwork that was done. Gave it a shot of primer. You will also notice that i have prepared and primered a wheel also. Will get into detail with that in next post. Gave the primer a sand and shot of paint. Ended up happy with the result. i knew i was never with my skillset able to blend it in without being noticeable but once the sill trim and door is closed its not too noticeable. better living everyone

https://www.trademe.co.nz/a/motors/cars/toyota/sprinter/listing/3238902889?bof=feIc2uXl cheap diesel car

I have run out of balls

I require pics of golf balls being fired through various materials plz. Car doors be good

Well I swapped the sensor back and it caught, and with a bit of encouragement it went...

lots of parts on ebay. postage is lots tho

Decided to drop the motor and box during lockdown. Didn't have an engine crane so just dropped it using a trolley jack where it was until I get my hands on one off the boys. Wasn't to bad doing it that way

One day I’ll update this thread in more detail but basically I also have this Yamaha, a 63 YG5. It was a bit slow so I swapped the motor out for one I picked up in S.E.A. It’s similar to a TTR110 kids dirt bike but no electric start. See the story here if you’re interested in the weirder side of small bikes.

If you ever want to sell this, Clint. Let me know. It's perfect and I would very much like to enjoy it at some point if the cards fall that way. I'll even promise not to call you about all the things I'll never do to it.

This runs. Is smokey as farq Wont rev hard but as half the clutch is missing thats not a priority just yet.

Solutions: Cutting it down, machined in lathe afterwards. M4 cap head to act as a pickup. This M4 drives the tab that turns the worm thread. Spacer made to add back on, what I cut off...but on opposite side. Tadah!! Fuck yeah! All sorted.

Unfortunately, I've got an office job so don't have any free time over lockdown. While the body is at the panelbeaters, I've been working on stripping the front valance and gaurds. Front valence wasn't too bad. Wee bit of bog, but I was able to mostly straighten out the wee dents without too much trouble. Can't say the same about the guards. Looked fairly good, but shitloads of bog and some horrendous repairs. Unfortunately there is a support for the guard, so I can't easily get to the back of the indented bit. I will have a go at welding on some tabs and pulling it straight. Don't mind a wee bit of bog, but that is taking the piss. Cut out the shitty bit at the front first, will sort that bit out first.

The correct Piston rings showed up quickly! The pistons cleaned up well and after getting the rusty, broken and stuck old rings out new hotness installed with lots of oil in the bores and moly grease on the bearings. Bores are pretty tapered based on the ring gap getting noticeably smaller as i moved it down the bores (and over spec all the way!) , but im just gonna send it. Installed the previously disassembled and cleaned oil pump, was pretty good under the grimness. Filled the gear housing with moly grease so its pre-primed New timing chain and gears, new crank nut and new welch/core plug. (turns out the 4 on the side are 32mm not 31mm, silly!!! More engine parts ordered... Everything turns over real smoothly, which is good enough for me. Turns out i didn't have all the seals. Its a weird stepped one that is only for Fiats that use these oil slingers, but ive taken a punt on a generic unstepped one to try. Future reference: Factory crank nose seal, shared with other fiats (500/600/850/1100/1500/2300 ) that use this oil slinger Seal 70/65x45x10

Nothing else to do this weekend but hang out in the garage and make brackets and fittings. Made a beefy bracket to fit in the A/C position, this will provide a mount for the supercharger drive layshaft, the forward belt tensioner and anything else I might choose to attach to it. Apparently Argon is not essential so I wasn’t able to purchase any. In this situation it was out with the trusty little Lincoln Electric arc welder to stick the bits of metal together. Everything went together well and the bolt holes even lined up when I was finished. Made an unnecessarily fancy brace for the manifold that may or may not be necessary and also made a fan shroud for the electric fan.

Something I have been working for on and off a year or so. @Dogwatch is keen on gardening and always figure that I have the shed for car stuff she deserves a shed for garden stuff. Looked at all the mitre 10 cheap shittas and they all looked horrific. Ended up seeing a crowd in TGA called the shed shop selling prefabbed sheds with basic wooden framing. Pulled the trigger and got free delivery through the home show. 10/10 would trade again very sturdy proper gutters and no rattles. Was awesome they clip wheels in the edges and roll it to where you wish. After a bit of exacvation Had a good pad to put shed on. @Beaver and @GuyWithAviators gave me a hand to make up a base to sit it on to get the shed off the ground, then made up a floor for it. Lined some walls, made a bench and put a bit of trim round the window and it was ready for paint. All the planks in the shed are planed down old fence palings. Gave it a lick of paint, popped some shelves in and made up some steel hooks and its good to go. Finally got the aliexpress solar lights in this afternoon shit they go good. Stoked at how it turned out is a bit fancier then we both anticipated but she does alot of gardening so it gets used alot. Its amazing how much nicer it feels inside with lined painted walls, feels like a proper shed not a cupboard.

Yeah, there's heaps of parts in the states for us made stuff. But who knows how long it'll take to be delivered. Last thing I bought at the beginning of the year to 7 weeks.

Bought a clip-on lens for my phone, most impressive.

Long story short, speedo driver unit for mechanical drive, adapted to fit a late model wheel that doesn't have mechanical driven speedo. Problem was this gap. The older shovelhead wheels have the bearing recessed in an inch, so that tab connects. Also they are mounted on the RH side. Mines on the left. Problems!!

hinges cleaned and blasted. Carefully hit the wiper motor too. The wiring sleeve has disintegrated and my brush on tape went hard in the cupboard. Mrs suggested epoxy glue/araldite so I drizzled that on and worked pretty well! Have painted half of it just waiting for some to dry, to mask off of. Was about to black epoxy-etch the hinges and inner of guards but it had gone weird.. I mixed the living piss out of it and decided to try it anyway. Avoided doing the hinges because they would be awful to blast again if it stayed soft. Heater blower, love this colour! Although VHT engine enamel, SP405 from memory..Left over from Mrs old 302 rebuild Guards got plenty of epoxy, narrowed the nozzle and jizzed it into all the gaps and holes, suck it corrosion; you’ve had your turn with this car Starter received a good clean and some paint. Wish I had a vapour blaster Anyway, I head back down south again tomorrow under level 3 to do more of the body! Here’s a nice example I spotted too

Ripped the old carpet out of the van. Exposed a bit of rust starting in the foot well, and some already nice rust repairs which are mint. Sanded all the glue down and sanded back the rust. It was surprisingly better than I expected. Was a good day of cleaning and sanding for the both of us. Its always exciting lifting the seats and carpet out of vehicles. Today we did a final sand and clean. We applied 2 coats of a rust converter primer, then 2-3 coats of a Colorpak toyota blue that I had stashed with my aerosol cans. It's a nice colour, wish i had more of it or could remember its name. It's done the trick anyway to seal it. Once we've got some carpet down it should look pretty good. Nice to know the rust has had a good seeing too.

Flak 88mm is going to be abandoned under some trees so followed the worn winter camo with some washed off road grime and mossy weathering.

Yes ! Im with Clint on this. Ive seen a few slammed ones on IG and has me feeling the same way

cylinders are like $5, just do the whole lot

Nah I sold it to a mate in Auckland and he keeps ringing me and telling me how great it is and how it's really cheap to run. Probably should have sold it to someone I didnt know then I wouldn't have to hear half drunk sharns about how good it would be with a turbo/lsd/4age/3sge/ 1uz knowing full well that talk is as far as it will ever go

Page 8 thread dredge. So I've still got this thing. I put it up for sake a couple weeks before lockdown and got bombarded with absolute fuckwits as per trying to sell something on Facebook. I got so sick of it in the end that I didn't want anyone else to own it so I decided to pull finger instead. So this lock down has been a whole lot of making do with what I have so I've been doing a bunch of rust repairs so the cab forward is now rust free and sitting in primer. It goes to paint in a couple weeks which I am looking forward to. Have decided to go white . While the truck is away getting painted I'll set to on the wellside which is going to be a massive undertaking

Surely this could have been worded a little differently

Pics..

Dude, that shit is sorted. It drives like a new car. Cheers all, your input is genuinely appreciated.