RUNAMUCK Posted August 4, 2021 Share Posted August 4, 2021 Whoever you are I hope you stole them off your employer, and used one of their courier bags to send it. /guess i owe someone a handy/panhead? 2 Quote Link to comment Share on other sites More sharing options...
tortron Posted August 4, 2021 Share Posted August 4, 2021 Bart, the pain of you skulking about to get some grommets, when an entire box can be delivered to you overnight, is unbearable 1 2 Quote Link to comment Share on other sites More sharing options...
Mop Head Posted August 4, 2021 Share Posted August 4, 2021 11 minutes ago, tortron said: Bart, the pain of you skulking about to get some grommets, when an entire box can be delivered to you overnight, is unbearable Thanks buddy. 29 minutes ago, RUNAMUCK said: /guess i owe someone a handy/panhead? Just spend that money on another box of grommets next time mate. 6 Quote Link to comment Share on other sites More sharing options...
tortron Posted August 4, 2021 Share Posted August 4, 2021 /some 3mm tyres for the daily 5 Quote Link to comment Share on other sites More sharing options...
sentra Posted August 4, 2021 Share Posted August 4, 2021 Keep him doubting so we can all claim a handy 2 2 5 Quote Link to comment Share on other sites More sharing options...
RUNAMUCK Posted August 4, 2021 Share Posted August 4, 2021 A hug, A high 5, And a handjob. 1 Quote Link to comment Share on other sites More sharing options...
kws Posted August 4, 2021 Share Posted August 4, 2021 I need to buy some long shank nuts to suit the hotwires I just bought for my Marina. I haven't used or bought shank nuts before, so I presume I just need the outer diameter to be a close fit in the hole and as long as I can fit without bottoming out on the hub? Are there any precautions I should take since the wheels will be nut centric not hub centric? Quote Link to comment Share on other sites More sharing options...
cletus Posted August 5, 2021 Share Posted August 5, 2021 Last time I bought some , the most economical way was to get them from super cheap But yes, snug fit in the holes, and not longer in the shank than the wheel is thickness wise And steel washers. Also if you are getting close to bottoming out the nut, make sure the wheel stud doesn't taper out at the bottom. I've seen that happen and the nut got stretched bigger at the shank end, making it very difficult to get back out of the wheel... 6 1 Quote Link to comment Share on other sites More sharing options...
chris r Posted August 5, 2021 Share Posted August 5, 2021 I got some metric shank nuts off supercheap and they were a bit shit. Threads were on the piss. Ended up finding a set off rock auto which were mint and significantly cheaper 1 Quote Link to comment Share on other sites More sharing options...
JustHarry Posted August 5, 2021 Share Posted August 5, 2021 Most/all tyre places sell them Ive got sets off mag n turbo before Quote Link to comment Share on other sites More sharing options...
chris r Posted August 5, 2021 Share Posted August 5, 2021 11 minutes ago, JustHarry said: Most/all tyre places sell them Ive got sets off mag n turbo before I must have dealt with a bunch or useless places. The company who supplies our wheel nuts/spacers didn't have any 1 Quote Link to comment Share on other sites More sharing options...
yoeddynz Posted August 5, 2021 Share Posted August 5, 2021 @kws try this... https://www.niceproducts.com.au/category/34757-wheel-nuts They have loads of sizes and once you know the ones you want you can order them through ripco. Quote Link to comment Share on other sites More sharing options...
locost_bryan Posted August 5, 2021 Share Posted August 5, 2021 @kws Performance Wheels are making new Hotwires, perhaps drop them a line about the best nuts to use? https://www.performancewheels.co.nz/product/hotwire/ Quote Link to comment Share on other sites More sharing options...
kws Posted August 5, 2021 Share Posted August 5, 2021 2 hours ago, locost_bryan said: @kws Performance Wheels are making new Hotwires, perhaps drop them a line about the best nuts to use? https://www.performancewheels.co.nz/product/hotwire/ Looking at the photos I have a feeling they probably use standard taper nuts, not shank nuts. Quote Link to comment Share on other sites More sharing options...
87creepin Posted August 5, 2021 Share Posted August 5, 2021 For door/suv tailgate actuators that aren't working, is it usually the dc motor in it that's gone bad? Quote Link to comment Share on other sites More sharing options...
Jeffs_Emporium Posted August 8, 2021 Share Posted August 8, 2021 Today I absolutely wrecked my fuel hard line at rear of car to the point where I need to trim it back and start again. Are cheap flare kits a no go? I only want to do this job once because scorpion back and 30 year old shit in eye sucks Quote Link to comment Share on other sites More sharing options...
tortron Posted August 8, 2021 Share Posted August 8, 2021 Come use mine if you want. Double flare kit Quote Link to comment Share on other sites More sharing options...
Jeffs_Emporium Posted August 8, 2021 Share Posted August 8, 2021 4 minutes ago, tortron said: Come use mine if you want. Double flare kit Please and thank you. It says you can't receive messages on here? Quote Link to comment Share on other sites More sharing options...
Nominal Posted August 8, 2021 Share Posted August 8, 2021 26 minutes ago, dspec_tt131 said: Today I absolutely wrecked my fuel hard line at rear of car to the point where I need to trim it back and start again. Are cheap flare kits a no go? I only want to do this job once because scorpion back and 30 year old shit in eye sucks Don't use a cheap flare kit IMO. I tried one for brakes and it sucked so much a bought an old used one that was so much better. 1 1 Quote Link to comment Share on other sites More sharing options...
gibbon Posted August 8, 2021 Share Posted August 8, 2021 has anyone ever repaired or gotten parts for these cheap vices? turns out this baby is a holdin' vice not a crushin' vice, i stripped the main nut on it. the nut is a barrel and plug thing cast together, I see this type of vice for sale all the time so presumably someone's dealt with this shit before in the meantime yo dawg i heard you like vices, heres some vice grips to grip yo vice while yo vice grips... (seemed to do the trick at least) 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.