Yowzer Posted October 15, 2016 Share Posted October 15, 2016 If the guy doing the paperwork couldn't tell the difference between a falcon and an rx3, then yes, technically you could. The reg name means very little. Ya see mis-regestered cars all the time. 3 Quote Link to comment Share on other sites More sharing options...
~Slideways~ Posted October 16, 2016 Share Posted October 16, 2016 If it was me i would heat shield the factory pipes rather than moving them inside the passenger compartment, ive never been a fan of having the fuel in the same space as the humans, even if it is allowed. Also making heat shields or using some of that sleeve type heat wrap over the pipes seems easier to me than re routing and attaching them correctly If you have wrapped the exhaust, and make an alloy shield, and there is an air gap, i think that would be fine. Thanks for the advice, I'll see what I can do with a combination of sleeve covering and a shield of some sort. Cheers Quote Link to comment Share on other sites More sharing options...
R100 Posted October 17, 2016 Share Posted October 17, 2016 If the guy doing the paperwork couldn't tell the difference between a falcon and an rx3, then yes, technically you could. The reg name means very little. Ya see mis-regestered cars all the time. I own a Mazda Cosmos according to the rego tag Quote Link to comment Share on other sites More sharing options...
morkster Posted October 17, 2016 Share Posted October 17, 2016 So technically I could list my Ford falcon as a rx3? Also he said there is no option for 808. Still a little confused here. I had a quick look at that listing the blackish/blue 13bpp sedan? IIRC the last 6 digits of the stc stamp matched the last 6 digits of the cert tag vin number, and i presume the car had a vin tag attached also.. i can't see the problem here. Call it what you want; 808 body and all tags match, all legal. Quote Link to comment Share on other sites More sharing options...
SiRge Posted October 17, 2016 Share Posted October 17, 2016 Where can I find out information about the legalities of fabricating a chain driven driveline for a car? Investigating if it's even worth the idea of putting a motorbike engine in a car 6 Quote Link to comment Share on other sites More sharing options...
Muncie Posted October 18, 2016 Share Posted October 18, 2016 Where can I find out information about the legalities of fabricating a chain driven driveline for a car? Investigating if it's even worth the idea of putting a motorbike engine in a car You can buy adapter flanges that replace the chain sprocket so you can bolt up a driveshaft direct to the engine for rearwheel drive. Another cool trick ive seen is using a Nissan R200 Lsd diff ditching the crownwheel and pinion and replacing it with the chain sprocket two small holes in the back cover of the diff cover for the chain to come thru and your away, the car i saw with this setup had a small ring gear sandwiched in as well with a starter motor so you could reverse. 1 Quote Link to comment Share on other sites More sharing options...
kicker Posted October 18, 2016 Share Posted October 18, 2016 Have seen something similar except case was ditched completely and a can had been made up to cover it to hold the oil. Quote Link to comment Share on other sites More sharing options...
kicker Posted October 18, 2016 Share Posted October 18, 2016 Here's a pic Quote Link to comment Share on other sites More sharing options...
SiRge Posted October 18, 2016 Share Posted October 18, 2016 More interested in the whole lubed chain flinging grease places or if there's requirements to have driveshafts secured in a particular way. Be silly for me to investigate something that can't be compliant regardless. I'm also not keen to spend several thousand on a quaife conversion box that some mini guys use. Should pay to say I've got a method someone else has used which seems fine, I just want to compare it to what the score sheet the cert guys might use to mark it effectively Quote Link to comment Share on other sites More sharing options...
Muncie Posted October 19, 2016 Share Posted October 19, 2016 The diff i saw was in that Hayabusa mini ute thing that slightly eccentric English guy built....... the one that builds weird mini based shit anyway it was all certed. 2 Quote Link to comment Share on other sites More sharing options...
kicker Posted October 19, 2016 Share Posted October 19, 2016 Just put a chain guard on like they have when in motorcycles, should have one more for chain breakage situations anyway. Chain wax stays put pretty well on chains 1 Quote Link to comment Share on other sites More sharing options...
crownin round Posted October 19, 2016 Share Posted October 19, 2016 Hey Clint, back on the adjustable arms idea i know you cant use the other main types due to welding to cast but is this design acceptable? it is fully forged cast not welded. https://www.facebook.com/plugins/post.php?href=https%3A%2F%2Fwww.facebook.com%2Fpermalink.php%3Fstory_fbid%3D1171863636205511%26id%3D119135261478359&width=500 Id also like to run either a 30mm bodylift with no steering extension to save on buying this piece and having to extend intakes, fuel filler,vacuum lines, etc. This is the steering shaft slip yokes engagement at 30mm body lift. Or run 50mm if that isnt alright there are 3 choices of steering extension. http://shop.snakeracing.com.au/ifs-hilux-steering-shaft-extension/ But for some reason these are not allowed in some of Aus so not sure about here. http://www.vehiclemods.net.au/vmn_steering_extension Uses extra factory toyota slip joint and extra bit of splined shaft or using the idea from above cut the upper spline of an wrecked hilux and use this with extra slip joint essentially a VMN extension from the wreckers. Would also like to fit larger tires but have never seen tire size on a placard so if i dont change rims from cert can i change tire sizes? ie il will be certed on 17x8s (to clear larger prado brakes) and 33s but want to eventually fit 35s am i allowed to swap or is it noted down? Otherwise i will fit the 35s first. Also is cutting a hole in radiator support panel legal as I will be running intercooler piping through it. (about 3 inch holes) To avoid scrub will also be trimming the body mount like so I assume this is all good as i seen one certed and done before but his looked pretty ragged. My struts are adjustable by changing the silver spacer shown below. Does this go on the cert plate even though its not thread adjustable? Thanks feel free to ignore this as i know its not old school. Quote Link to comment Share on other sites More sharing options...
Transom Posted October 22, 2016 Share Posted October 22, 2016 What's the go with using wheel PCD adaptors with alloy wheels that use shank nuts ? Everything I read says tapered nuts locating adaptor to hub and tapered nuts locating wheel onto adaptor Are shank nuts ok on adaptors ? Or do I need wheel centring adaptor centric ring gizmos as well? Is countersinking old alloy wheels to run tapered nuts as dodgy as it seems ? Quote Link to comment Share on other sites More sharing options...
SiRge Posted October 22, 2016 Share Posted October 22, 2016 They're just studs. Shank nuts are fine. Main thing is the hub ring must be correct size Quote Link to comment Share on other sites More sharing options...
Willdat? Posted October 25, 2016 Share Posted October 25, 2016 Friend of mine is wanting to pop seats from a Super Custom into the back of a 4WD Hiace, The two local certifiers have differing opinions if this can be done without cert. One reckons it can done if there is no welding - hence no 'modifying'. The other reckons that even bolt together adapters need cert as using the mounts in a way other than factory is 'modifying' them. This friend likes to do things by the book so a clear answer would be sweet. Cheers! Quote Link to comment Share on other sites More sharing options...
cletus Posted October 25, 2016 Share Posted October 25, 2016 Where can I find out information about the legalities of fabricating a chain driven driveline for a car? Investigating if it's even worth the idea of putting a motorbike engine in a car do able has been a few cars certed like that somewhere on the LVV website theres something about them, but im not sure where. might have been a newsletter mentioning something about not legally having to have a reverse gear Quote Link to comment Share on other sites More sharing options...
cletus Posted October 25, 2016 Share Posted October 25, 2016 Hey Clint, back on the adjustable arms idea i know you cant use the other main types due to welding to cast but is this design acceptable? it is fully forged cast not welded. https://www.facebook.com/plugins/post.php?href=https%3A%2F%2Fwww.facebook.com%2Fpermalink.php%3Fstory_fbid%3D1171863636205511%26id%3D119135261478359&width=500 hard to say without seeing in person Id also like to run either a 30mm bodylift with no steering extension to save on buying this piece and having to extend intakes, fuel filler,vacuum lines, etc. This is the steering shaft slip yokes engagement at 30mm body lift. Or run 50mm if that isnt alright there are 3 choices of steering extension. http://shop.snakeracing.com.au/ifs-hilux-steering-shaft-extension/ But for some reason these are not allowed in some of Aus so not sure about here. probably ok depending on what its made of http://www.vehiclemods.net.au/vmn_steering_extension Uses extra factory toyota slip joint and extra bit of splined shaft or using the idea from above cut the upper spline of an wrecked hilux and use this with extra slip joint essentially a VMN extension from the wreckers. would be ok Would also like to fit larger tires but have never seen tire size on a placard so if i dont change rims from cert can i change tire sizes? ie il will be certed on 17x8s (to clear larger prado brakes) and 33s but want to eventually fit 35s am i allowed to swap or is it noted down? Otherwise i will fit the 35s first. tyres never get listed on cert plate, i would write it on the paperwork though, as anything bigger than 5% bigger overall diameter, needs cert Also is cutting a hole in radiator support panel legal as I will be running intercooler piping through it. (about 3 inch holes) yep To avoid scrub will also be trimming the body mount like so I assume this is all good as i seen one certed and done before but his looked pretty ragged. looks ok to me My struts are adjustable by changing the silver spacer shown below. Does this go on the cert plate even though its not thread adjustable? i would write it down as an adjustable platform suspension, because it is adjustable via spacers disclaimer- anything i say may be different from what another certifier says and no guarantees that what i get shown in a photo will pass a cert whether it looks ok or not 1 Quote Link to comment Share on other sites More sharing options...
cletus Posted October 25, 2016 Share Posted October 25, 2016 What's the go with using wheel PCD adaptors with alloy wheels that use shank nuts ? Everything I read says tapered nuts locating adaptor to hub and tapered nuts locating wheel onto adaptor Are shank nuts ok on adaptors ? Or do I need wheel centring adaptor centric ring gizmos as well? Is countersinking old alloy wheels to run tapered nuts as dodgy as it seems ? with adaptors, the requirement is to use tapered wheel nuts, or locate on the center spigot if the wheel nuts are not tapered so use centering rings on the wheels attached by shank nuts and you will be fine Quote Link to comment Share on other sites More sharing options...
cletus Posted October 25, 2016 Share Posted October 25, 2016 Friend of mine is wanting to pop seats from a Super Custom into the back of a 4WD Hiace, The two local certifiers have differing opinions if this can be done without cert. One reckons it can done if there is no welding - hence no 'modifying'. The other reckons that even bolt together adapters need cert as using the mounts in a way other than factory is 'modifying' them. This friend likes to do things by the book so a clear answer would be sweet. Cheers! has it already got seats in the back of the 4x4 one? if its registered as a 3 seater and hes putting more seats in, then definitely needs cert. if it already has seats, and he is bolting in some different/better ones, this applies- 7.1 http://lvvta.org.nz/documents/suplementary_information/LVVTA_LVV_Cert_Threshold.pdf 1 Quote Link to comment Share on other sites More sharing options...
Willdat? Posted October 25, 2016 Share Posted October 25, 2016 has it already got seats in the back of the 4x4 one? if its registered as a 3 seater and hes putting more seats in, then definitely needs cert. if it already has seats, and he is bolting in some different/better ones, this applies- 7.1 http://lvvta.org.nz/documents/suplementary_information/LVVTA_LVV_Cert_Threshold.pdf Already has seats - just your very basic bench. The idea behind the Super Custom seats is that there's something safer for kids. 7-1 was what I was looking at. Does modified = welded, or any adaptation of standard mounting points, even if not welded? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.