chasinthemirage Posted December 12, 2022 Share Posted December 12, 2022 What's the go with replacing bump stops? Haven't got much clearance between the pinion snubber on the wagon, it's 65mm tall overall. Can I replace it with an aftermarket one that's shorter? Virm says they can't be modified but doesn't mention replacing them with an aftermarket option. Quote Link to comment Share on other sites More sharing options...
Popular Post cletus Posted December 12, 2022 Popular Post Share Posted December 12, 2022 4 hours ago, chasinthemirage said: What's the go with replacing bump stops? Haven't got much clearance between the pinion snubber on the wagon, it's 65mm tall overall. Can I replace it with an aftermarket one that's shorter? Virm says they can't be modified but doesn't mention replacing them with an aftermarket option. Technically, modifying or replacing bump stops with non standard ones, requires cert. But, a scallywag with no regard to following the rules of the land, an outlaw if you will, would likely get away with it if it looked standard. The aforementioned scallywag should be careful that a replacement shorter bump stop still limits the travel before the driveshaft hits the tunnel though 7 2 3 Quote Link to comment Share on other sites More sharing options...
Motu Posted December 13, 2022 Share Posted December 13, 2022 Some of those bump stops you get in a strut kit are generic, some don't even work and get tossed. I've had them blow apart because they are too long. I'll give them a trim....if it's got a boot you can't see them anyway...or even if they are fitted. 1 Quote Link to comment Share on other sites More sharing options...
Shakotom Posted December 13, 2022 Share Posted December 13, 2022 No welding of steering or suspension components but can I weld new mounts for brake hoses/abs lines to the bottom of a adjustable coilover body? - mounts for these differs from what car needs Quote Link to comment Share on other sites More sharing options...
RUNAMUCK Posted December 14, 2022 Share Posted December 14, 2022 *no welding forgings. Quote Link to comment Share on other sites More sharing options...
chasinthemirage Posted December 14, 2022 Share Posted December 14, 2022 On 12/12/2022 at 18:25, cletus said: Technically, modifying or replacing bump stops with non standard ones, requires cert. But, a scallywag with no regard to following the rules of the land, an outlaw if you will, would likely get away with it if it looked standard. The aforementioned scallywag should be careful that a replacement shorter bump stop still limits the travel before the driveshaft hits the tunnel though Thanks for this, it's shaping up to be a lot of measuring and hassle for the sake of lowering the car another 3cm haha. My old man suggested some bags of cement in the boot, might be an easier way to go! Quote Link to comment Share on other sites More sharing options...
cletus Posted December 15, 2022 Share Posted December 15, 2022 On 14/12/2022 at 11:22, Shakotom said: No welding of steering or suspension components but can I weld new mounts for brake hoses/abs lines to the bottom of a adjustable coilover body? - mounts for these differs from what car needs Yep if it's just a steel coilover body that's fine Quote Link to comment Share on other sites More sharing options...
187inc Posted December 15, 2022 Share Posted December 15, 2022 Ball joint spacers.. looking at replacing the rear leaves in the Hilux with some slightly higher heavy duty ones (40 or 50mm max-more for load capability than lift). If the front end is drastically lower once this is done I was thinking about winding the torsion bars up to get the front end closer to the rear height. I've read ball joint spacers are popular to correct the angles which winding the T-bars up will create, and prevent the ride from becoming harsh. Are they legal? They would only be maybe 25mm. Edit: 2003 4WD Hilux if that matters. Quote Link to comment Share on other sites More sharing options...
cletus Posted December 15, 2022 Share Posted December 15, 2022 Not usually something that can be certified Because of the extra leverage on the mount points they often end up cracking the arm Ages ago I did a cert on a lifted Colorado that had spacers, I put a gopro on the top suspension arm and it flexed an alarming amount with a ball joint spacer fitted 1 1 Quote Link to comment Share on other sites More sharing options...
187inc Posted December 15, 2022 Share Posted December 15, 2022 1 hour ago, cletus said: Not usually something that can be certified Because of the extra leverage on the mount points they often end up cracking the arm Ages ago I did a cert on a lifted Colorado that had spacers, I put a gopro on the top suspension arm and it flexed an alarming amount with a ball joint spacer fitted Thanks that's exactly the clarification I was looking for. Definitely doesn't sound worthwhile. 1 Quote Link to comment Share on other sites More sharing options...
VintageSpecial Posted December 16, 2022 Share Posted December 16, 2022 I know there aren't too many vintage people here but does anyone know anything about a comment in the presidents message section of Beaded Wheels (page 4) saying there is a new category of certifiers expressly for pre 1990 vehicles? It doesn't sound like it was anything they were involved in, they were just told about it at a meeting they say, and that it should help getting deregistered pre 1990 vehicles back on the road. It mentions new certifiers in place by mid 2023 and not much else really. I know there are already rules around exemptions for pre 1990 vehicles (https://www.nzta.govt.nz/vehicles/vehicle-types/vehicle-classes-and-standards/exceptions-to-the-standards/) but that's all I have found so far on NZTAs site. I can't find anything on the LVVTA site about it at all. I was going to ring them to ask but being the end of the year I imagine they are mad busy so thought I would ask here first. Thanks, Simon Quote Link to comment Share on other sites More sharing options...
Popular Post cletus Posted December 17, 2022 Popular Post Share Posted December 17, 2022 That will be for repair cert not lvv cert, LVVTA now runs the repair cert system. I believe they intend to run different rules for pre 90 vehicles, in an effort to help people who are restoring older cars as applying the same rules for an HQ holden and a 2020 kia does not make sense 11 1 Quote Link to comment Share on other sites More sharing options...
VintageSpecial Posted December 17, 2022 Share Posted December 17, 2022 Ah, I did know that LVVTA was now looking after the repair stuff too now so that makes sense, thanks. They don't make it clear in the mention in the magazine. Quote Link to comment Share on other sites More sharing options...
SOHC Posted December 24, 2022 Share Posted December 24, 2022 Would this be legal? Exhaust existing out the side. Quote Link to comment Share on other sites More sharing options...
Nominal Posted December 24, 2022 Share Posted December 24, 2022 As long as it is behind the rear door I think. Quote Link to comment Share on other sites More sharing options...
cletus Posted December 24, 2022 Share Posted December 24, 2022 That's like that from factory on those things 4 Quote Link to comment Share on other sites More sharing options...
Bling Posted December 24, 2022 Share Posted December 24, 2022 I'm going to say if you DIY'd that, you'd be out of luck, doesn't look to be past the rear opening of the door. Maybe it works as it's pointed away from the opening. Full marks for the straight parking though. It's illegal to take photos with an iPad with your dog hanging out the window too. 2 1 Quote Link to comment Share on other sites More sharing options...
AllTorque Posted December 24, 2022 Share Posted December 24, 2022 https://vehicleinspection.nzta.govt.nz/virms/in-service-wof-and-cof/general/exhaust/exhaust-system#tab1 see note 7. Legal 1 1 Quote Link to comment Share on other sites More sharing options...
kws Posted December 26, 2022 Share Posted December 26, 2022 Does it matter if a previous owner has painted over my VIN plate? Doesnt look tampered with, and has been there since about 1995, but was painted at some point along with various other bits under the bonnet. Plates are on hold, so it's just for a WOF. Quote Link to comment Share on other sites More sharing options...
AllTorque Posted December 26, 2022 Share Posted December 26, 2022 According to the VIRM, it is a fail https://vehicleinspection.nzta.govt.nz/virms/in-service-wof-and-cof/general/vehicle-identification/vin-and-chassis-number ”Condition” Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.