Flash Posted September 6, 2022 Share Posted September 6, 2022 Hiya All. I'm about to start investigating a temperature related issue on one of my projects and I'm thinking a good place to start would be getting myself one of those infrared temperature guns so that I can check out what is actually going on at each point in the cooling system. Prices seem to vary on the units and I don't really want to spend more than I need to as it's not something I'm going to get a lot of use out of. But, I also don't want to buy something that isn't accurate enough as I could end up chasing my tail. I'd appreciate any suggestions on what unit to buy and also any tips or tricks on how to use the gun as I'm a newbie to all of this. Ta in advance Quote Link to comment Share on other sites More sharing options...
Lord Gruntfuttock Posted September 6, 2022 Share Posted September 6, 2022 Could you borrow one from an electrical outfit? They use them for checking hot spots in switchboards, substations, lines etc. Good ones are several thousand $$$ 1 Quote Link to comment Share on other sites More sharing options...
tortron Posted September 6, 2022 Share Posted September 6, 2022 I got a fairly cheap one. It can tell if one side of the radiator is hot and if one side is cold, I think it was about 30 bucks, I use it quite a bit on motorcycle engine cases and radiators when running in and tuning This is a point and shoot and it displays the temperature. Not a screen of heat signatures 1 Quote Link to comment Share on other sites More sharing options...
Thousand Dollar Supercar Posted September 6, 2022 Share Posted September 6, 2022 I use one regularly at work. Although it sends out a pinpoint laser dot so you can tell where it's aimed, the actual measurement area gets bigger as you go farther away from the gun. You don't need to consider that if you're using it at close range - it's effectively a point measurement unless you're far from something. While you're holding down the trigger, mine continuously updates the average temp of the measurement area as well as updating the maximum temp of that session. Those two numbers are all it gives you. I've used it on the thermostat housing of the Jag because I was suspicious of the temperature gauge on the dash. 1 Quote Link to comment Share on other sites More sharing options...
azzurro Posted September 6, 2022 Share Posted September 6, 2022 I have a cheap aliexpress gun style one. It shoots an optional red dot and has a colourful led screen that only funtion is to show the measured temp at approx where the dot is. Have used to tune sideys (exhaust runner temp) check radiadiators, wonder about double glazing, diagnose busted oven elements and similar. Reccomended tool, feels solid and seems surprisingly sensitive as you wave it around and gives a good sense of relative temps of things. 4 Quote Link to comment Share on other sites More sharing options...
Bling Posted September 6, 2022 Share Posted September 6, 2022 Used to use a cheap aliexpress one at work, seemed reliable and accurate enough. Will be the same as above, there will be a million of the same thing on ali. 1 Quote Link to comment Share on other sites More sharing options...
NickJ Posted September 6, 2022 Share Posted September 6, 2022 Cheap guns only have one emissivity setting so can vary wildly depending on surface, a cold black item can read higher than hot polished stainless etc. Expensive guns have full emissivity control but you can never be bothered to change it -Hold down 2 buttons in a sequence you can never find the instructions to remember. Easy way to get around this is buy a cheapish option and just place a small square of masking tape on the surface as a target, i've found it to be as accurate as you'd look for in such a device. 8 Quote Link to comment Share on other sites More sharing options...
sheepers Posted September 6, 2022 Share Posted September 6, 2022 as above, most guns available wont give you an accurate reading on a shiny surface so stick a bit of black tape on it or something. also heat radiation/hot air flow coming up between you and the thing your measuring will effect the reading so be mindful of taking readings above exhaust mannys etc. 1 Quote Link to comment Share on other sites More sharing options...
Flash Posted September 6, 2022 Author Share Posted September 6, 2022 Fellas, I really appreciate all of the advice and tips. Thanks very much. Quote Link to comment Share on other sites More sharing options...
datlow Posted September 7, 2022 Share Posted September 7, 2022 I grabbed one from bunnings as only place locally that had stock at the time, as per above it works for the small amount of times ive needed it https://www.bunnings.co.nz/ozito-8-1-distance-to-spot-ratio-infrared-thermometer_p0229649 1 Quote Link to comment Share on other sites More sharing options...
sr2 Posted September 7, 2022 Share Posted September 7, 2022 I bought a cheap on one Bangood some years back and wouldn't be without it. It's surprisingly accurate for the price and most of the time you're looking at comparative temperatures like top/bottom radiator hoses or exhaust headers. It's saved a a fortune on brake indicator (thermochromic ) paint on the race car and most importantly is very handy when brewing beer! 3 Quote Link to comment Share on other sites More sharing options...
Motu Posted September 10, 2022 Share Posted September 10, 2022 I've had a Raytec for about 20 years, it was a cheaper version, and you can get ones just as good for a good price these days. Even for just diagnosing a misfire - point at exhaust ports...that's the one ! A very important part of my tool kit, but the 9 volt battery is a pain, expensive things...I have one battery and move it around my devises. A USB one would be nice in the modern world. 1 Quote Link to comment Share on other sites More sharing options...
RUNAMUCK Posted September 10, 2022 Share Posted September 10, 2022 I bought one from the tool shed for around $30 on special. I've never actually used it in anger yet. At work I have a Fluke (or flume? Idk) which I use for measuring ground temperatures when doing ice inspections. I dunno what that one cost, but I was told "it wasn't cheap" by the guy who did buy it. They both seem to work the same. (Never done a comparison side by side) 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.