shizzl Posted August 8, 2020 Author Share Posted August 8, 2020 On 07/08/2020 at 10:40, yoeddynz said: Tell me more about that hino. What's its wheelbase and over all max weight? We have pretty much sold ours (awaiting contract to be done) 1 Quote Link to comment Share on other sites More sharing options...
Popular Post shizzl Posted September 6, 2020 Author Popular Post Share Posted September 6, 2020 Well I've sold all of the hunter engine parts that I have. Carbs, head etc.. Got the engine disconnected ready to pull out for collection next weekend. Have a breast plate on its way which should work with the crossmember. Got a 12a carb but needs a strip and clean. Found an electronic dizzy too with modules, these seem to be very hard to find these days.. Only need a driveshaft yoke, colling fan, fuel pump and hosing etc and an alternator with bracket. Then start piecing this together. 14 Quote Link to comment Share on other sites More sharing options...
shizzl Posted September 7, 2020 Author Share Posted September 7, 2020 On the hunt for m16/type16 Ford calipers, and capri vented discs if anyone happens to have any floating round. Also rwd mazda driceshaft/yoke Quote Link to comment Share on other sites More sharing options...
yoeddynz Posted September 7, 2020 Share Posted September 7, 2020 Ask @maxted about a drive shaft- he might have a spare 1 Quote Link to comment Share on other sites More sharing options...
shizzl Posted September 12, 2020 Author Share Posted September 12, 2020 Remarkably, the engine and box went straight in.. With some fighting and cussing. All bolted up nicely enough. Shifter hole is about 70mm off, but that puts it in a better location for reach. 1 Quote Link to comment Share on other sites More sharing options...
yoeddynz Posted September 12, 2020 Share Posted September 12, 2020 1 hour ago, shizzl said: Remarkably, the engine and box went straight in.. With some fighting and cussing. All bolted up nicely enough. Shifter hole is about 70mm off, but that puts it in a better location for reach. what box is it? If its a series 2/3 box then you can move the shifter forwards by around 70mm or something- if that helps. But sounds like ya don't need to Fake edit- I looked at the pic again and see its a series 1 box. Quote Link to comment Share on other sites More sharing options...
shizzl Posted September 12, 2020 Author Share Posted September 12, 2020 Yeah s1 box. I did that trick yo a s4 box in the ute I built back in the day. 2 Quote Link to comment Share on other sites More sharing options...
dabuzz Posted September 16, 2020 Share Posted September 16, 2020 Yeeeooow - haven't seen this thread since the heart transplant! Best decision you ever make - best! Quote Link to comment Share on other sites More sharing options...
tortron Posted September 16, 2020 Share Posted September 16, 2020 kiwi speed hunter - Meth hunter? ver niiice Quote Link to comment Share on other sites More sharing options...
oldrx7 Posted December 14, 2020 Share Posted December 14, 2020 any updates @shizzl Quote Link to comment Share on other sites More sharing options...
shizzl Posted December 17, 2020 Author Share Posted December 17, 2020 Moved house and have been getting the stockcar sorted, so the old girl hasn't had any time spent on it unfortunately. Ready to pu it for a rebuild and putting together though 1 Quote Link to comment Share on other sites More sharing options...
oldrx7 Posted December 17, 2020 Share Posted December 17, 2020 All good - things take time right - Where did you find the ready made rx crossmember for it? Quote Link to comment Share on other sites More sharing options...
shizzl Posted December 18, 2020 Author Share Posted December 18, 2020 A guy in huntly had it made for his, but sold the engine etc. 2 Quote Link to comment Share on other sites More sharing options...
shizzl Posted February 17, 2021 Author Share Posted February 17, 2021 Bs update... Pulled the engine to strip and inspect, everything is wasted beyond use.. Apart from the housings, Theyr mint.. So I went and bought another 12a...lets see how this goes. 3 Quote Link to comment Share on other sites More sharing options...
kyteler Posted February 17, 2021 Share Posted February 17, 2021 If there's a rotor too fucked to do anything with I'd like one for my shed if you want to sell it ? 1 Quote Link to comment Share on other sites More sharing options...
shizzl Posted February 28, 2021 Author Share Posted February 28, 2021 On 17/02/2021 at 18:16, kyteler said: If there's a rotor too fucked to do anything with I'd like one for my shed if you want to sell it ? There's definitely a fucked one 4 Quote Link to comment Share on other sites More sharing options...
shizzl Posted February 28, 2021 Author Share Posted February 28, 2021 12a bridgeport round 2....fight This engine looks super clean inside, lots of compressions. Came with an electronic dizzy and s4 alt. I chucked the side draft on it but need a tall port manifold cos this one is missing one of the bolt tabs. Waiting to go it... 7 Quote Link to comment Share on other sites More sharing options...
yoeddynz Posted February 28, 2021 Share Posted February 28, 2021 On 17/02/2021 at 18:16, kyteler said: If there's a rotor too fucked to do anything with I'd like one for my shed if you want to sell it ? I'm keen on any spare 12a rotor for my shed too- to fill my empty 12a housing on the shelf. Quote Link to comment Share on other sites More sharing options...
shizzl Posted March 12, 2021 Author Share Posted March 12, 2021 Got the engine and box in place for hopefully the last time.. Clutch fork and release bearing is also in there. Cut the hole for the shifter.. Need to straighten the shifter as it angles too much towards the drivers seat. In reverse it gets close to the seat. If I straighten it, it'll be perfecto. Ordered all of my exhaust parts, and have a new manifold flange plate.. So look out for sketchy welds and bs looking noise cannon build. Ordered a new Ali radiator and 14" fan to match the nice oil cooler. Will need to find stock oil cooler hoses or get the braided ones shortened to suit. Also need a few bolts for the bellhousing and starter so that can be finished off. Driveshaft measured and will get dropped off next week. Not sure if I'm going to use standard rubber fuel line or braided, I've never fitted braided fittings before.. We'll see. Clutch slave is ordered ready for collection, then make a hose up for it. Then it's mainly all wiring stuff, lengthen wiring for alt, coils, starter and gauges. Wiring up thermo fan switch etc. It needs to be finished by May 13th as I move out of my workshop then.. Want to do a coilover mid to the spare struts too.. Along with capri discs and escort calipers. 5 Quote Link to comment Share on other sites More sharing options...
shizzl Posted March 16, 2021 Author Share Posted March 16, 2021 Playing with the primaries. Collector to go on.. Then the flexi and the rest of the zorst. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.