My name is Russell Posted March 30, 2010 Share Posted March 30, 2010 Sick dryer! what power rating does that puppy have?! Sex E Quote Link to comment Share on other sites More sharing options...
thegreatestben Posted March 30, 2010 Share Posted March 30, 2010 So hard to focus on the shiny in those pics Need the following Quote Link to comment Share on other sites More sharing options...
eke_zetec_RWD Posted March 30, 2010 Share Posted March 30, 2010 pinto dryer man, running 20psi. clothes get blown dry! Quote Link to comment Share on other sites More sharing options...
peteretep Posted March 30, 2010 Share Posted March 30, 2010 your the man, your car is so awesome as is your workmanship Quote Link to comment Share on other sites More sharing options...
eke_zetec_RWD Posted March 30, 2010 Share Posted March 30, 2010 your the man, your car is so awesome as is your workmanship sush did u get your car sorted? Quote Link to comment Share on other sites More sharing options...
peteretep Posted March 30, 2010 Share Posted March 30, 2010 ha, i stopped trying and am taking the motor out to run my brake lines this weekend with my new land rover master cylinder, once thats done then ill try getting running again Quote Link to comment Share on other sites More sharing options...
Josh Posted March 31, 2010 Share Posted March 31, 2010 I hate you/ am extremely envious/jealous haha, looks super nice man and bet it will perform just as well. Quote Link to comment Share on other sites More sharing options...
yoeddynz Posted April 1, 2010 Share Posted April 1, 2010 Fuck that seems seriously quick- 0-100 in what, maybe 6 secs? very very nice workmanship there fella- lovely job! Quote Link to comment Share on other sites More sharing options...
eke_zetec_RWD Posted April 1, 2010 Share Posted April 1, 2010 Fuck that seems seriously quick- 0-100 in what, maybe 6 secs? very very nice workmanship there fella- lovely job! id say its a lot faster than that on full boost. my new engine will be ready for install end of this weekend. went to put pistons in last night and the bloody oil rings are too deep so i have to machine the pistons a little deeper to accept them. cant wait. Quote Link to comment Share on other sites More sharing options...
eke_zetec_RWD Posted April 2, 2010 Share Posted April 2, 2010 argh ffs. machined pistons to suit the new rings sweet. put number 1 and 4 into block turn over to tdc. and the fucking piston is hanging out the deck of the block. i must of got supplied yb cosworth rods instead of pinto rods! now i got to pull apart again, then machine crowns of pistons down. my bad i should of measured the lengths. could be a good thing because i wanted to up the cr a little so il cc the head. want to go up to around 8.5 to 1. Quote Link to comment Share on other sites More sharing options...
peteretep Posted April 2, 2010 Share Posted April 2, 2010 surely it would be easier to get replacement rods and deny any modification of oil ring diameters, whats standard meat on top of a piston? Quote Link to comment Share on other sites More sharing options...
eke_zetec_RWD Posted April 2, 2010 Share Posted April 2, 2010 heaps of meat on top, they dished anyway. a longer rod will only make the rod/stroke ratio better. its 60thou longer, but i might not remove that much from piston. Quote Link to comment Share on other sites More sharing options...
FuzzayD Posted April 2, 2010 Share Posted April 2, 2010 This looks AWESOME! I like the nudey ladies above your lathe Quote Link to comment Share on other sites More sharing options...
Truenotch Posted May 9, 2010 Share Posted May 9, 2010 Mint! Time for us to live in fear? Really keen to see how it goes after a retune... Quote Link to comment Share on other sites More sharing options...
eke_zetec_RWD Posted May 9, 2010 Share Posted May 9, 2010 yea will give her a few weeks before a tune. sounds mint tho. no oil leaks so far!! Quote Link to comment Share on other sites More sharing options...
Truenotch Posted May 9, 2010 Share Posted May 9, 2010 WHAT!!!??? A pinto with no oil leaks? Fuck. Quote Link to comment Share on other sites More sharing options...
eke_zetec_RWD Posted May 9, 2010 Share Posted May 9, 2010 WHAT!!!??? A pinto with no oil leaks? Fuck. yet, i glued the fuck out of everything Quote Link to comment Share on other sites More sharing options...
eke_zetec_RWD Posted May 11, 2010 Share Posted May 11, 2010 drove it home tonight, took some timing out on boost to be safe. starter motor reduction box/cover adaptor plate smashed into 3 pieces before tho! standard starter motor is sooo shit compaired!!! will make a new one out of smash proof materials Quote Link to comment Share on other sites More sharing options...
Horse25 Posted May 18, 2010 Share Posted May 18, 2010 Looking forward to these results A LOT, don't forget to take a video! Quote Link to comment Share on other sites More sharing options...
Truenotch Posted May 18, 2010 Share Posted May 18, 2010 365HP at the wheels.... Place bets now! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.