Beaver Posted January 26, 2017 Share Posted January 26, 2017 @kyteler tried to PM you but it wouldn't work, but rekon you could grab that cam when you are up to it? Would be mucho appreciated. 1 Quote Link to comment Share on other sites More sharing options...
kyteler Posted January 26, 2017 Author Share Posted January 26, 2017 One moment caller Quote Link to comment Share on other sites More sharing options...
Seedy Al Posted March 8, 2017 Share Posted March 8, 2017 Shit yes, buy some spats Go full JAP custom Quote Link to comment Share on other sites More sharing options...
kicker Posted March 8, 2017 Share Posted March 8, 2017 Hey boover, I have a 71C bellhousing you could test with. I like your motivation/direction Quote Link to comment Share on other sites More sharing options...
Beaver Posted March 8, 2017 Share Posted March 8, 2017 I have no idea what a 71C gearbox is but keen to see if it fits. Quote Link to comment Share on other sites More sharing options...
kyteler Posted March 8, 2017 Author Share Posted March 8, 2017 it's a designation used across all Nissan boxes (it's to do with ratios, etc. the 'C' stands for Close the other option is W at the end. Guess what that stands for). lerl. I assume he means one for an RB though. Not that it would matter cause an L bell should work also. Quote Link to comment Share on other sites More sharing options...
KKtrips Posted March 8, 2017 Share Posted March 8, 2017 Monster Garage Factoid - the 71 stands for 71mm between centres of the main and lay shaft in the gearbox. (just like the 63 in 63a means it is 63mm from centre to centre) 5 Quote Link to comment Share on other sites More sharing options...
kyteler Posted March 8, 2017 Author Share Posted March 8, 2017 I likely knew that at some point but now I do again, thank-you Kesse Kames. Quote Link to comment Share on other sites More sharing options...
KKtrips Posted March 8, 2017 Share Posted March 8, 2017 Wink.. Boyd Kytelerton 1 Quote Link to comment Share on other sites More sharing options...
kicker Posted March 8, 2017 Share Posted March 8, 2017 Sorry, was being lazy, I mean I have a bellhousing for a FS5W71C box which can be found on some RB's Silvias etc Also have a FS5W71B box with poo synchros The deez bellhousing i have can be swapped straight onto the 71C and lets you bolt it up to L series Enough ramblings, I should do something with my gearbox bits one day. Quote Link to comment Share on other sites More sharing options...
Beaver Posted March 8, 2017 Share Posted March 8, 2017 Oh mean, keen to grab it from you and see if it will bolt up. Quote Link to comment Share on other sites More sharing options...
kicker Posted March 8, 2017 Share Posted March 8, 2017 We can see if our parts dock nicely 4 Quote Link to comment Share on other sites More sharing options...
fletch Posted March 8, 2017 Share Posted March 8, 2017 FS5W71C Floor Shift 5 speed Warner synchros 71mm between shafts centers C revision box. (Larger countershaft front bearing, larger 1st/2nd synchros+ selector) R4W71B Remote (column) 4 speeds B revision. Etc FS5C71B Same but the C stands for Porsche type steel servos(synchros) I have found these in random zed's but in no particular pattern. RFB twenny debt and 25 no debt and s13/14 have the C type box with the 6 bolt plate at the back holding the shifter. The bellhousings are mostly interchangeable. If you try to run a C onwards gearset in a B housing you will need to machine a bit of clearance for the larger counter gear and bearing, and drill out the 1st/2nd selector rod hole from 14 to 16mm. The B gearset goes straight into the C housing with the C bearing, but you need to sleeve the selector hole down to 14mm. The gearbox revisions went all the way to H. The later ones had synchros on reverse and double synchros on 2nd. I have a good selection of boxes, parts, new synchros etc in stock if you need bits. Barry out... 4 Quote Link to comment Share on other sites More sharing options...
Beaver Posted March 8, 2017 Share Posted March 8, 2017 Lol. i only need it to bolt up a starter motor 1 Quote Link to comment Share on other sites More sharing options...
fletch Posted March 8, 2017 Share Posted March 8, 2017 19 minutes ago, Beaver said: Lol. i only need it to bolt up a starter motor Haha didn't see that. Quote Link to comment Share on other sites More sharing options...
kicker Posted May 21, 2017 Share Posted May 21, 2017 Hey mein, I should have some bolts, 12x1.25 or something eh? Also have a spacer that may or may not fit off an l series auto Quote Link to comment Share on other sites More sharing options...
Beaver Posted May 21, 2017 Share Posted May 21, 2017 Yep yep m12x1.25. Spacer will likely not fit but worth a shot anyway if I'm grabbing some bolts. Will just use washers if not haha Quote Link to comment Share on other sites More sharing options...
kicker Posted May 21, 2017 Share Posted May 21, 2017 Word, will dig stuff out 3 Quote Link to comment Share on other sites More sharing options...
kicker Posted May 21, 2017 Share Posted May 21, 2017 Had a quick look on my way out, found two spacers #1 (flat) OD 88mm ID 32mm PCD 60mm Thickness 4mm #2 (top hat) OD 88mm ID 20mm Snout OD 30mm Height 17mm yada yada Quote Link to comment Share on other sites More sharing options...
Beaver Posted May 21, 2017 Share Posted May 21, 2017 Yeh nah they won't work but thanks for looking! Keen to grab those bolts of you come across them (will only be temporary loan) Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.