twosmoke Posted December 20, 2010 Share Posted December 20, 2010 . Quote Link to comment Share on other sites More sharing options...
drftnmaz Posted December 20, 2010 Share Posted December 20, 2010 i've heard the ramp rates are different and can do weird things like throw the valve open you can get 260 degree cams for hydro lifters but you do have to upgrade the springs to suit (i've got some jun ones for my s13 motor) but these prob have more lift also Quote Link to comment Share on other sites More sharing options...
twosmoke Posted December 20, 2010 Author Share Posted December 20, 2010 . Quote Link to comment Share on other sites More sharing options...
drftnmaz Posted December 20, 2010 Share Posted December 20, 2010 yea, i just meant to point out that you can use hydro lifters with bigger cams... you don't have to go solid, but need springs sounds like a sweet cheap upgrade, up the springs and try Quote Link to comment Share on other sites More sharing options...
twosmoke Posted December 20, 2010 Author Share Posted December 20, 2010 . Quote Link to comment Share on other sites More sharing options...
mikuni Posted December 20, 2010 Share Posted December 20, 2010 You could get some cams grinded/reprofiled for not much more than $150 and still have the timing good enough to run without vernier cam gears if using original cams, why not just do that? I talked to Franklin Cam Services and they seemed quite knowledgable about how far you could push hydro lifters. Quote Link to comment Share on other sites More sharing options...
KKtrips Posted December 20, 2010 Share Posted December 20, 2010 I copied this from another forum There's two issues. 1) the solid lifter must be set up with clearance to allow for differential expansion in the valvetrain, so the cam to drive it has an introductory ramp that is long and slowly changing, to pick up the mass of the valvetrain gently. An HLA cam does not provide this "soft pickup" so may be less suitable for use with solid lifter valvetrain. 2) Solid lifter cams are usually used with lighter lifters and springs, so they can have steeper opening ramps (knowing the lower opening forces won't break through the cam face). Heavier HLA valvetrain may lead to excessive forces and wear on a solid lifter cam Quote Link to comment Share on other sites More sharing options...
Jase Posted December 20, 2010 Share Posted December 20, 2010 qft^ a regrind and antipump lifters designed for your engine. Quote Link to comment Share on other sites More sharing options...
twosmoke Posted December 21, 2010 Author Share Posted December 21, 2010 . Quote Link to comment Share on other sites More sharing options...
Jase Posted December 21, 2010 Share Posted December 21, 2010 for what purpose do you need more power? are you certain it's power you need not torque? for instance if you were building this for a daily a high torque cam suits better as it will give you better acceleration and driveability, a high power cam will give you more top end but won't be neccessarily suitable, remembering torque = twisting force ....acceleration and driveability power = rate of work ....more top end speed of course if you have huge power torque generally comes with it , but for an na set up gains are marginal and targeting the motors specific use is important Quote Link to comment Share on other sites More sharing options...
nick_m Posted December 21, 2010 Share Posted December 21, 2010 If its a budget smash together motor. Just do it. Whats the worst that happens, it destroys it self. it was a budget motor Anyway Quote Link to comment Share on other sites More sharing options...
mikuni Posted December 21, 2010 Share Posted December 21, 2010 While you are raping GTi-R parts you should get some quad throttles and run it on a squirt. Keen to see an "on-the-cheap" NA SR20 build actually. Assuming you are staying NA. Quote Link to comment Share on other sites More sharing options...
Snoozin Posted December 21, 2010 Share Posted December 21, 2010 There was an sr20ve running at one of the dyno days I attended with quads and cams. Made a very peaky 114kw atw which was 15 to 20kw behind the B18CR's running on the day. I was slightly gutted since I'd been keen to see how a tickled VE went for a while. Quote Link to comment Share on other sites More sharing options...
mikuni Posted December 21, 2010 Share Posted December 21, 2010 Yeah, i've heard mixed results about the VE. I think theres potential there to just build a better dedicated DE engine, but it would be a little more peaky. VE would be a good base/factory engine though, just drop it in a track car and go. Heres a dyno sheet from TP a year or 2 ago, with a VE making 126kw at the wheels http://i462.photobucket.com/albums/qq34 ... lchart.jpg Theres a video of it somewhere too, and it just sounds insane. Shakes the camera etc, actually quite funny. Quote Link to comment Share on other sites More sharing options...
nick_m Posted December 22, 2010 Share Posted December 22, 2010 Ve ports are way to large from factory. They really are just horrendously huge.They certainly have potential but a bolt on only VE will never match a Honda VTAK with bolt ons. Bit disappointing being THAT far behind a b18c. They are normally atleast within ball park. Although no one has really had good results with ITB's on VE's, again I reckon its cause the ports are too large. I'm gonna go to town on my VE head. I'm going to fill the port floors and get an actual appropriately sized port and run ITB's. Hopefully with good results Quote Link to comment Share on other sites More sharing options...
mikuni Posted December 22, 2010 Share Posted December 22, 2010 Ve ports are way to large from factory. They really are just horrendously huge.They certainly have potential but a bolt on only VE will never match a Honda VTAK with bolt ons. Bit disappointing being THAT far behind a b18c. They are normally atleast within ball park. Although no one has really had good results with ITB's on VE's, again I reckon its cause the ports are too large. I'm gonna go to town on my VE head. I'm going to fill the port floors and get an actual appropriately sized port and run ITB's. Hopefully with good results Sounds good man. Theres a couple of forum members on here who have played around with filling ports a little - Toyota motors often suffer a similar problem to what you are describing. I'm definitely keen to see a detailed build/tech thread when you satrt playing around with the VE head. Quote Link to comment Share on other sites More sharing options...
Seedy Al Posted December 22, 2010 Share Posted December 22, 2010 im also keen to see how that would work out, nothing like closing the engine ports to achieve better engine Quote Link to comment Share on other sites More sharing options...
Spencer Posted December 22, 2010 Share Posted December 22, 2010 Off topic but got a pic of the VE ports for comparison? Quote Link to comment Share on other sites More sharing options...
mikuni Posted December 22, 2010 Share Posted December 22, 2010 Hard to gauge size from this one This isn't VE, but still relevant to thread (kind of). "High port RWD" SR20DE apparently. Quote Link to comment Share on other sites More sharing options...
twosmoke Posted December 22, 2010 Author Share Posted December 22, 2010 . Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.