oldrx Posted January 8, 2011 Share Posted January 8, 2011 Put this q on ausrotary too but thought you chaps prob have an opinion? I want to set up a fuel return line on my Weber side draft (DCO). Im using the common holley fuel pressure regulator that isnt a return style im 99% sure. And a Carter pump (7psi 72 gal p/min from memory). NA 13b EP fwiw. Would it work if i simply bolt on the fitting off of a nikki onto the Weber (it all bolts up fine btw) and use the itake and return fittings off of that? I know it has a little one way valve in it with a flat spring that holds it closed under low pressure that acts kind of like a fpr. This could be easily removed if it was too much of a restriction, and the valves hole (larger brass hole in big pic) could also be drilled out bigger if needed. This is all after the holley fpr obviously. Am i on the right track here? This is the setup on Factory Nikki This is it disasembled This is it with valve and spring removed. Installed on Weber Quote Link to comment Share on other sites More sharing options...
peteretep Posted January 8, 2011 Share Posted January 8, 2011 I don't think you really need to run a return line from the weber at all, the regulator will stop that from happening Quote Link to comment Share on other sites More sharing options...
Rookie Posted January 9, 2011 Share Posted January 9, 2011 ^ This Quote Link to comment Share on other sites More sharing options...
yoeddynz Posted January 10, 2011 Share Posted January 10, 2011 Ditto- All the webers i've seen fitted never have returns. So long as inlet pressure is the right amount you should be fine. Quote Link to comment Share on other sites More sharing options...
oldrx Posted January 11, 2011 Author Share Posted January 11, 2011 I'll try it with and without. I thought running without return would wear fuel pump out a lot faster though? Quote Link to comment Share on other sites More sharing options...
KKtrips Posted January 12, 2011 Share Posted January 12, 2011 Fuel pumps are designed to do exactly what you are worried about.. Quote Link to comment Share on other sites More sharing options...
Unclejake Posted January 12, 2011 Share Posted January 12, 2011 I agree with what others have said. Don't put a return on the Weber but do ensure that you have the float level set correctly and invest $60 in a Repco fuel pressure/vacuum gauge so you can set the FPR to something that works for you. I used 3.5psi with good results Quote Link to comment Share on other sites More sharing options...
Chrome_GT Posted January 14, 2011 Share Posted January 14, 2011 Original Capri: 32/26dgav no fuel return line at all, the location is cast solid. Currently fitted: 32/36dgav with return line. From a 78 Cortina - i kept the return line, fuel sender etc just incase i wanted to retrofit this to the capri. I just added a Y connection in before the filter and ran the return line back to that. Hopefully the return line also has a check valve otherwise this could be allowing fuel to bypass the filter. http://www.fordcapriforum.com/forum/viewforum.php?f=13 from above site - may apply in your case too: "Did you know why the Weber 32/36 carb has a fuel return line? It's nothing to do with overfilling or anything like that! In fact, up to 1976 they didn't have a return. The carb is designed to draw in the fumes from the fuel in the float chamber to prevent them building up. Trouble is, if you leave the car idling on a hot day, the fumes created are excessive and affect the mixture sufficently to increase the emissions leaving the exhaust. With increasing legislation against pollution etc, it was decided to put in a return line so that a constant flow of cooler fuel was passing through the carb, hence reducing the fume build up and lowering emissions.:"" "Weber's official method for fitting the later carb to an earlier car is to T the return hose back into the supply from the pump a couple of inches back from the carb, using a T piece with a one way valve in it" Quote Link to comment Share on other sites More sharing options...
sholdowa Posted January 17, 2011 Share Posted January 17, 2011 All my RS2000's had return lines on them, with a restrictor on the return line. Both in and out were marked with an arrow pointing outwards, but if you connected them the wrong way around it would idle but not run. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.