Flash Posted October 29, 2022 Author Share Posted October 29, 2022 With my newly ordered radiator slowly meandering its way up from Victoria I figured I'd get ahead of the game by making a start on the battery relocation. Now the old Muzzy boot is not the most spacious that you have ever come across with the full size spare wheel and mandatory Mustang branded kit bag that contains my emergency tool roll and jumper cables taking up most of the space available. Adding a battery into the mix is going to make things decidedly cozy. So what to do : 7 Quote Link to comment Share on other sites More sharing options...
Flash Posted October 29, 2022 Author Share Posted October 29, 2022 Battery Relocation - Chapter 1 A few weeks back I ordered a 5-meter length of 230-amp battery cable. My plan was to route this through the right-hand rear quarter panel and then down the inside of the door opening cunningly hidden under the factory thread plate. The only other thing needed was a hole in the firewall and a rubber grommet to protect the cable. Whilst I was chucking in the big battery cable, I also ran a 5mm wire to my fuse box. This will allow me to keep power to my sound system and other bits and bobs even if my main battery cable is switched off by my anti-theft kill switch. A few photos of the cabling which is now in position: The wiring on my factory fitted starter solenoid together with the additional wiring for my thermo fan relays and fuses needs a bit of a tidy up, but I'll do that once I've finalised the plan in terms of thermo fans. More about that subject later. Thanks for looking. 8 Quote Link to comment Share on other sites More sharing options...
Flash Posted October 31, 2022 Author Share Posted October 31, 2022 Battery relocation - Chapter 2 Since the new battery cables are sitting on the right-hand side of the boot, it only made sense that I should locate the battery there. After a bit of thinking I figured the best solution would be if I could tuck the battery up against the side of the rear quarter panel, but that would necessitate cantilevering the whole thing over the void between the boot floor and the side. Not impossible to do. It will just need some beefy support as the battery is not the lightest thing around. I scratched around in my shed and came up with a set of angled brackets that would do nicely. Drilling the mounting holes was the trick bit as I don't have one of those fancy 90 degree drills, but by dropping the right-hand exhaust I was able to squeeze my drill past the rear leaf spring and managed to poke through the 4 mounting holes needed. The brackets look a bit skew in this photo, but I had no choice as the panel has a slight angle to it. Nothing a few custom spacers won't fix. Â 4 Quote Link to comment Share on other sites More sharing options...
Flash Posted October 31, 2022 Author Share Posted October 31, 2022 Battery relocation - Chapter 3 With the foundation brackets mounted in place I returned to the shed for another scratch around and came out with an old battery tray left over from one of my donor Mitsi vans. Had a good bit of surface rust but was otherwise solid. Chucked it in my vinegar bath for a day and it came out absolutely mint. Poked a few extra holes in it, cobbled up a few spacers and gave it a test fit. Works perfectly. Slapped a bit of primer and satin black on that sucker and we were ready to rock. 7 Quote Link to comment Share on other sites More sharing options...
Flash Posted October 31, 2022 Author Share Posted October 31, 2022 Battery relocation - Chapter 4 Next step was to pull out the original engine bay battery shelf to create the additional space needed for my bigger radiator. The whole thing is held in with 4 bolts and came out easy enough. What I really like about the Mustang tray is that it holds the battery down with a little foot clamp rather than the Mitsi tray which uses the old hooked threaded rods and a cross bar over the top of the battery. Checked the dimensions on the Muzzy tray and its just slightly smaller than the Mitsi tray, so I figured why don't I see if I can modify the Muzzy tray to bolt inside the Mitsi tray. That way I get a nice double thickness tray to help support the battery over the void and at the same time I get to keep the neater foot clamp style battery mount which looks way neat. Luckily the angle bracket on the Mustang tray is only held on with 3 tack welds, so those were easy enough to break. Cleaned the Muzzy tray up, poked a few more holes, slapped on some paint and the battery relocation is now done and dusted. Very happy with the result. 5 Quote Link to comment Share on other sites More sharing options...
Flash Posted October 31, 2022 Author Share Posted October 31, 2022 With the battery now safely tucked up in its new home, I turned my attention to fine tuning the rest of the boot layout. First up is the relocation of the spare wheel as its original position now clashes with the battery. Tried a few things and settled on trying to tuck the spare up against the back seat backing board. All that is needed is for me to replicate the factory hold down bracket that looks like so: Â 2 Quote Link to comment Share on other sites More sharing options...
Flash Posted October 31, 2022 Author Share Posted October 31, 2022 Didn't want to start hacking things off the floor so rummaged around in the shed and came out with this little bracket : 1 Quote Link to comment Share on other sites More sharing options...
Flash Posted October 31, 2022 Author Share Posted October 31, 2022 Trimmed the replacement bracket down a bit, poked a few holes, slapped a bit of satin black on it and called it done. 4 Quote Link to comment Share on other sites More sharing options...
Popular Post Flash Posted October 31, 2022 Author Popular Post Share Posted October 31, 2022 And, that's the boot more or less sorted. The existing boot liner is a bit tatty, but new ones are available so I'll order a fresh one sometime in the future and will then cut up the old one to make a neat little battery cover. That should complete the look nicely. I'm happy with the new spare wheel position as it has freed up some extra useful boot space. Thanks for looking. 10 Quote Link to comment Share on other sites More sharing options...
Popular Post Flash Posted October 31, 2022 Author Popular Post Share Posted October 31, 2022 ..... and the courier just arrived. Woohoo ! Guess what I am cracking into tomorrow .... 12 Quote Link to comment Share on other sites More sharing options...
Popular Post Flash Posted November 2, 2022 Author Popular Post Share Posted November 2, 2022 Cooling Issue - Chapter 9 A while back as part of my cooling diagnostic exercise I flushed the system, but I figured it was worth giving things another good flush before installing the new radiator. Managed to do three flushes over the past two days and I reckon I've got things as clear as I am going to get them. So, this morning I cracked into the radiator upgrade. First step was to strip the front of the car which I managed to achieve before morning smoko. With the old radiator out of the car I was able to put the new and old next to each other for a quick comparison. My plan is to test fit the new radiator to make sure that my tranny cooling lines and new radiator hoses all line up and once I'm totally happy with the fitment, I'll then pull the rad out to butcher the bigger opening. More to follow later in the day.  11 Quote Link to comment Share on other sites More sharing options...
Popular Post Flash Posted November 3, 2022 Author Popular Post Share Posted November 3, 2022 After checking that my new radiator hoses and the tranny cooler lines all line up, I spent the rest of the morning cutting out the sides of the radiator support panel to expose the full core of the new radiator. The bite sized chunks out of the right-hand panel are the cut outs for the original a/c lines. The new rad is temporarily bolted in position, but I can't finalise the mounts and filler panels until I've sorted out my new a/c condenser location and its mounts. Talking about a/c, just before lunch I swapped a few yarns with my local supplier who has suggested replacing the current 18 inch condenser with a 23 inch unit which will reduce the generated heat. With a bit of luck I can pick up the new unit tomorrow and then button everything up. Thanks for looking. 13 Quote Link to comment Share on other sites More sharing options...
Popular Post Flash Posted November 9, 2022 Author Popular Post Share Posted November 9, 2022 I'm still plugging away at the new radiator and a/c condenser install. I ended up sourcing a 23" x 14" condenser. It's a bit shorter than the new radiator, but the next available size was 25" x 14" which would have been way too big for my current opening. I've mounted the condenser as far left as possible for two reasons. First up it was easier to run the a/c lines this way as I didn't want them rubbing on the new radiator core. Secondly, I figured with the radiator inlet and outlet both being on the right-hand side and the radiator therefore having a natural tendency to push a higher percentage of the coolant up this side of the radiator it made sense to have the unrestricted airflow on this side. I don't really know if this will help, but hey ... it is what it is. With the condenser test fitted I made some templates for the two additional mounting brackets required and I also carved a little filler panel to cover the old a/c hose holes. Figured I'd refresh the front panel whilst I have the grill and valance off, so that is looking a lot neater now. A few "in progress" photos: 16 Quote Link to comment Share on other sites More sharing options...
Popular Post Flash Posted November 17, 2022 Author Popular Post Share Posted November 17, 2022 I've been in a bit of a holding pattern on the Mustang front. Needed to wait for my next town run to buy some rubber seals and angled aluminium in order to fabricate the radiator surrounds. Wanted to seal the edges up as much as possible to force the air through the a/c condenser and radiator. Still need to seal around the edge of the rad shroud, but I ran out of rubber, so I'll grab some more on my next town trip. With that all done, this morning was the first start up to check for leaks. The good news is no coolant leaks. The bad news is that I had a leak from one of the tranny cooler lines right on the joint where the threaded pipe end enters the cooler. Should have checked it before I pulled the car out of the garage as that would have saved me from having to clean up the floor. It's amazing how much pissed out in such a short run. Oh, well, that's just how it goes sometimes. Quick fix with a bit of plumber's tape and she is good as wood. Time to put the front back together again so I can do some road testing. 16 Quote Link to comment Share on other sites More sharing options...
Popular Post Flash Posted November 18, 2022 Author Popular Post Share Posted November 18, 2022 Spent a few hours yesterday putting the Mustang's face back on, then headed out for some spirited driving this morning. Got to say that I'm really chuffed with the results. Previous temp on the thermostat housing with smaller radiator and a/c condenser was 209 F. Highest I could get today was 178 F. And that is with a 180 F thermostat fitted. Top rad hose was previously 184 F compared to 169 F now. Bottom rad hose was previously 163 F compared to 147 F now. Celebrated with a blue berry muffin for morning smoko, then cracked into installing the rest of the a/c components. Original hoses are back in with new o rings. Bottom hose is now slightly long for the job, but I managed to tuck the excess under the front lip, so that was good. I've also chucked in a new drier bottle and pressure switch for good measure. The a/c hasn't operated since 2014, so it will be interesting to find out if there are any issues with the rest of the components. I won't know until Steve the mobile a/c guy pays me a visit sometime next week. Finished off the morning by giving the old girl a bit of a bath. Thanks for reading. 15 Quote Link to comment Share on other sites More sharing options...
Popular Post Flash Posted December 22, 2022 Author Popular Post Share Posted December 22, 2022 Well, it's been almost a month since I got the a/c up and running in the old Muzzy and I might add that the timing was pretty perfect as we have experienced a few scorching days this month including one rather balmy day that reached 34 degrees C. I've notched up just under 300km in this period and the car is running really well. I've only got two minor complaints. First up I've noticed a bit of condensate that drips down one of the a/c pipes inside the cabin. It then meanders down the accelerator pedal stalk and lands perfectly on top of my foot. I've stuck my head under the dash and the last inch of a/c pipe before it enters the fan unit is exposed. I've got a short length of foam cladding which I'll need to slit down the side to fit, but hopefully with that and a few cable ties I can solve the issue. The second issue was a little more annoying, but again a relatively easy fix. I'd noticed that the a/c blower fan would speed up as my engine revs increased and would then slow down when I decelerated. I figured that with the extra load of both my Spal thermo fan and the a/c blower fan running almost continuously, the poor old factory alternator was struggling to keep up with the extra load. A quick poke around the internet and I set my sights on a black Aeroflow 140 amp single wire jobbie that the vendor reckoned was a direct bolt on for any of the small block Ford engines. Yeah, right, I've heard that one before. Anyhoo, I hit the "Buy Now" button and the parcel arrived earlier this week. So, this morning I cracked straight into it. Pulled the old unit out, then taped up all of the external regulator wiring and tucked it out of the way. Made up a meaty power and earth cable and chucked the new alternator on. Much to my surprise the new unit bolted up perfectly. Took the Muzzy out for a quick squirt around my test track and hey presto .... the a/c blower fan now holds its revs no matter what the engine is doing. Winner, winner. I had read a few horror stories about the factory ammeters getting fried up due to the higher amperage. I'm a bit sceptical, but I disconnected the gauge before fitting the new alternator anyway. I'm going to temporarily fit a 2-amp inline fuse before I connect it up again just as a bit of insurance. I also need to remove the factory fitted external voltage regulator and associated wiring as I don't plan on ever going back to the original setup. So that is another small job to do. A few photos of the new and old units for your viewing pleasure. Thanks for looking.  14 Quote Link to comment Share on other sites More sharing options...
Popular Post Flash Posted December 23, 2022 Author Popular Post Share Posted December 23, 2022 Hey, hey .... it's wiring tidy up day. I had to disconnect my left headlight and blinker light to create enough slack in the front wiring loom in order to work on it. Next step was to unwrap the harness and what a mucky job that is. With the wrapping off I was able to remove the wires associated with the now defunct external voltage regulator. Then a quick wrap with some fresh cloth tape before tucking what is left of the harness back behind the radiator support panel. And that's another small job jobbed. 12 Quote Link to comment Share on other sites More sharing options...
Popular Post Flash Posted December 26, 2022 Author Popular Post Share Posted December 26, 2022 I've been pondering what to do on the Muzzy from a fuelling point of view for a few months now. Allow me to set the scene: A previous owner had fitted a brand-new Holley 600 4-barrel carby to the mighty 289 small block. Although the car runs really well, it can be a bit "fumey". Chatting to a couple of folk more knowledgeable than myself, the general consensus was that she was over fuelled. This was supported by the fact that the car cold starts easy as with absolutely no choke required. Another clue is the fact that after a short drive with the windows down I smell like I've just been out mowing the lawn. Whilst "eau de unleaded" may appeal to some, it gets a bit tiresome after a while. Anyhoo, supplied with the car was the original 2-barrel intake manifold as well as two old carbs, a 2 barrel Holley and an old Autolite. Both look pretty manky and would need a full refurb. I'm not really keen to go back to a 2-barrel, so I discarded that option. My next thought was to look out for a Holley 465, but they are getting hard to find and are also pretty spendy. I tracked down a family run performance shop down in Victoria who specialise in refurbing old carbs and they were offering a reco'ed and bench run 465 without me having to supply a core unit for just under $900 delivered to me in Queensland. So again not exactly cheap. Now back in the day when I was playing around with my V8 powered Bedford van I ended up trying and discarding 3 different carbies before I was happy. First up was a Quickfuel, then a Holley and finally a refurbed Rochester Quadrajet. With the cost of each carby plus a few dyno tunes thrown in for good measure the spend was getting up there. I was never 100% happy with the van as even with the Rochy it guzzled the juice and at one point I even toyed with fitting EFI, but at that time the cost of off the shelf EFI kits was pretty eye watering. So, getting back to the Muzzy I decided that a bit more research was needed before pulling the trigger on the carby. Spent many a night with my good friend Google and Youtube. Even pestered a few USA based Mustang gurus for their advice and eventually ended up setting my sights on the Fitech EFI. Now it just so happens that my local Autobarn is a Fitech stockist and earlier in the week I dropped by and saw that they had one Fitech Master Kit in stock. Today they were having a 25% off Boxing Day sale so first thing this morning Mrs Flash, our wee dug and myself hopped into our trusty old Bongo van and headed through to town. Got there 10 minutes before store opening and I was second through the door. Literally bowled over the poor shop assistant to get my hands on the kit, but get it I did. This is my first foray into the land of aftermarket EFI, so I am on a steep learning curve. Let the fun commence. 16 1 Quote Link to comment Share on other sites More sharing options...
Flash Posted December 29, 2022 Author Share Posted December 29, 2022 I've kicked off step one of the EFI install which is determining a location to mount the mini surge tank that came with my EFI kit. So, first off a bit of scene setting: Fitech offer three fuel delivery options. Option One is an eternal high-pressure rail mounted pump. Whist this is the most cost-effective solution from an initial purchase point of view, in reading through the Fitech related tech info that is out there it seemed like a number of folk have battled to maintain consistent fuel pressure with this setup, largely due to pump cavitation caused by poorly setup input feeds. Most solutions seem to involve opening up the fuel tank to install baffles and bigger diameter fuel pickup lines and the like. This is way above my skill set and being a tight arse, I wasn't keen to outsource this to someone else. Option Two involves retro fitting an in tank high pressure pump. Again, this entails some tank modifications which are way out of my comfort zone. Option Three consists of a mini surge tank that incorporates an in-tank pump. This is the most expensive option from a purchase point of view, but to me it looks like the simplest way to achieve consistent fuel pressure without having to undertake "open tank" surgery. So, Option Three it was. All that the surge tank needs is a low-pressure input line and an output line that feeds excess fuel back to the factory fuel tank. In terms of surge tank location the options are endless. Some folk have mounted the surge tank in the boot using a low pressure 12-volt pump as the feeder and then running a high-pressure fuel line all the way to the throttle body. Another option is to mount the surge tank in the engine bay using the factory standard low pressure fuel line and mechanical fuel pump as the feeder. This is the option that I am going with for a number of reasons. First up I'm more comfortable with retaining the low-pressure fuel line under the car. Secondly, I'm keen to retain the original factory mechanical fuel pump as this allows me to re-install the carby with relative ease should I need to. My thinking being that if ever my EFI lets me down I'm able to get the car back up and running on the carby with very little effort. So, where to find a spot in the engine bay for the little tank ....... Well luckily, I have a bit of real estate that was recently created by my battery relocation exercise and it's just perfect for my needs. The tank comes with a mounting bracket that can be mounted on the bottom or side of the tank. I've gone for the side mounting option which will allow me to tuck the tank up hard against the radiator support panel. First step was to change over the mounting bracket:   9 Quote Link to comment Share on other sites More sharing options...
Popular Post Flash Posted December 30, 2022 Author Popular Post Share Posted December 30, 2022 Poked a few holes in the radiator support panel, chucked a few nuts and bolts into the mix and the surge tank is now safely tucked up in its new location. I've ordered a few rolls of 3/8 bundy tube, so when those pitch up, I'll install the return line back to the factory tank. I'll also bend up a short length to extend the feed line from the mechanical pump to the surge tank. Thanks for looking. Â 14 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.