craig_b

cheers AL and Cletus, and yup RX sedan with no roll cage etc

Hey there, i've had a bit of a search through the lvvta website and searched on this forum but havent found the answers im looking for, what i want to know, will a low backrest and no head rest seat go through cert? same as the links provided below, nzkw classic recliner and racetech seat. as i am looking at replacing unknown brand large bucket seats and not looking for a full on race looking seat. racetech seat NZKW seat Next question is, what requirements or standards do seatbelts need to be built too? my rear belts have paint on them and drivers belt has light fraying so i am looking at replacing the lot with a set from Pac performance, there's no details on their site about what standards the belts are made too and i have not received a reply by email form them yet, link to belts below Seatbelts any info is much appreciated. cheers

You guys spend alot of time in the lawnmower and yard trimming thread? Haha Cheers man will look this stuff up

Ahaha. By lawnmower i mean rotary, aka chicken cookers,egg beaters etc etc. 2 day rotary event like power cruise but for engines without them piston thingys "REunion"

Hey dudes and dudettes. In February ill be coming up from dunedin for the lawnmower (rotary) convention at taupo motorsport park. Have got 3 days to get to taupo then after the event got 6 days to get too chch. From taupo i want to head west to catch up with family in hawera for a night. If anyones got some suggestions of sweet roads and scenic shit to check out anything legit let me know, im pretty flexible with times etc and what happens just know i want to be in taupo on the 11th & 12th then ChCh on the 18th. And... From the 20th/21st of Feb i will be doing another mission back to the North heading to Auckland for the weekend of the 24th, but want to head up the east coast this time so same applies. If theres any decent scenic roads or anything worth checking out let me know. Let the fuel be burnt.

Im keen to leak some oil in Cromwell on the way to Rangiora but will just have too see what days i can get off work

keen bogan here, but will be taking the tang to timaru for the boy racer convention 10th/11th. such a busy time of year not enough time for activities

was hoping that wasnt the case anymore for the cert height, its not a baja race truck so 610mm is a bit impossible for hub center to guard haha. i wonder how this could be fixed without re-cert. also.. if i want to get rid of the personalized plate and put a normal plate on will it need re-cert or just a updated plate?

hey there, just picked up a new car and have a couple of questions, 1) with adjustable suspension is the measurement on the cert plate from the center of the hub to the guard, or from the guard to the ground ? as my cert plate is showing 610mm +/- 5%, so either its from guard to ground or its a cert plate error. 2) if its registered as a 4 seater and you have no rear seats or seat belts will this still pass a wof ?

and then....

that looks awesome

Is anyone doing the monkey tomorrow?

also keen but i only get 1 weekend off a month so that will be the deciding factor

cheers man, but has been sorted

Yo. Does anyone in dunedin have a coil spring compressor? Ive got 2 new springs to fit to my truck and keen to borrow one for 15 mins. Let me know if your keen

Yo

Whats happening in Tauranga this thurs/fri/sat ? Came up for jet sprints from dunedin and like to party. If anything going down send me a PM or reply

Mint man. Just flick me a txt to sort when would suit. Ive got a couple days off at the moment. 0273373630

Yo guys, wondering if theres anyone in dunedin thats keen to help me rope tow my F100 from Green Island to Kaikorai valley (approx 5km) to a storage unit. Ive got a ute and a rope just need a pilot for either vehicle. Need to start doing some work on it to be ready for end of jan. Cheers

damn you for reminding me, isle of man tt, goodwood, and gatebil all around same time of year, was thinking about going to the states next year but that might not happen now

ill be keen to hear about how it goes for you rookie, theres a fair few events id love to attend overseas. will you be camping there?

that looks like an awesome site, cheers man

ive got no worrys waving around oxy/acetylene. just want some advice on what is / isnt needed for the machine and different materials. how to set up the machine for different materials, good/bad brands.

steel cap or non steel cap?

Hey whats up, anyone in Dunedin or Otago that knows how to tig weld and willing to teach? looked at doing a course at otago polytechnic but due to me working stupid hours it isnt really achievable. want to learn for hobby purposes not to get into engineering / metal fab as a job. any info or ideas throw my way cheers.