escortwags

ignore - sorted

very good, shall keep you posted on how it goes

Ok so deal is pinion is at -5 and gearbox will sit at about -3 Will be running a two piece d shaft. Is this going to kill my universals? Gap to floor is less than 20mm from the head

cheers for the info yo! Will post a pic up tonight of my said issues and see if anyone can see the solution

Cars to low and it's fucking me off (my 616) Half way through re mounting top arms on the diff to sit inside the chasis etc. Started questioning the diff heads angle and if its fucked So yeh what's the perfect angle, have a 2 piece driveshaft if that helps. If someone says near straight it's bye bye floor and hello angry bastard

Mine were mint, I threw them away I'm pretty sure sorry....

how low is your god dam cross member to the ground? my adjustables are at the top of their height at that picture + captive, they have enough play to make the xmember to lay frame haha I'm thinking rolling on 13's will be near impossible unless on sheets of glass, 16's will make roads plausible, if your still on the look out for simmo's theres heaps on Ebay at the moment going for around $500 if your down jsut buy some and ill pick them up and ship

Sad face Any lower than this and it's undriveable even by my standards

Let the Capella low battles begin!

Jesus christ! Have they been sitting inside a bath full of salt water?

My solution = poor man/bong fiend solution hahaha

Had a similar issue many moons ago with my escort, no matter what they would never bleed AT ALL (couldnt get random air out. SOLUTION.... Get one of those hand dildo bike air pumps, make a massive tampon out of toilet paper as you would to seal a cone on a bong, jam it on top of the master cylinder where you put fluid it, open up bleed nipple and pump the fuck out of it, work mint for me hahahha

Definitly clutch! Will bet my sack on it. had the exact same symptoms on an old car and our newer one. Will be a combination of bung flywheel and warn out plate. Our wrx had mad shudder when cold, would dissapere when hot, only fix was machining the flywheel and a new clutch, still had slight shudder on new clutch until it bed into the flywheel properly and is now mint. Still a gay cunt of a car though. Heard of myth of riding the Holley shit out of the clutch may help to try and wear off gay spot, but doubt that would work Useless info that probably won't help

Is world famous in NZ, cars off to SD PERFORMANCE and getting a whole heap of shit done to it, so stay tuned

This car makes me happy

hmmm this could help me in my quest into not cutting the crap out of the firewall/tunnel niiice, $300 is a pretty sweet price to How small are these buggers compared to a standard starter? Ive got a brand new series 3 RX7 starter but the bitch is way to fat/a little bit too long to get close to fitting

hahaha all good. Reading that cracked me up was a good solid burbon infused ramble. Good news is the art of stuffing a 10.5" rim in the arse without tubs is well underway , just have to wait for stupid freight from oz to nz

It's all coming together nicely. What makes ones chassis not great to start with? More than a few solid race cars built from rx2's 10% car 90% how you drive the fucker. And fuck getting on the band wagon of a car that lives off bolt on parts and easy to source Internet knowledge, Hate if your Gona hate all I know is I'm on the right track and drunk az fuck haha

Buy them anyway! I'll make em cheaper just for you. Starts with d ends with t. Only selling those bits to buy even more expensive replacements haha

Meh we'll see...Everything is a lame trend when it comes to cars lowering one, wheels, engine etc. it's all about execution that's the key my son.

hmmm dont think I'll sell it now, pictures make 1000 thoughts disappear , will post proper ones hopefully late next week when it gets pushed out for some natural light/a quick clean. the narrowest of all narrow pictures hahahha On another note, anyone know anyone that sells JDM stickers, need enough to cover a bonnet. Iv'e got the pingas just need the goods

Cheers for all the motivtional speeches. Still thinking I'm gona sell it. Have to wait till Thursday for the pics though! So yeh if you know of anyone keen let me know Saweet

new found flushness should be posted on monday, mates being a c**nt and wont send me pictures till hes 100% finished with the setup/cleaned car/ pushed into natural sunlight Im hanging out way to hard for them the bastard!!?, he reckons business card jammed in the guard flush, but we'll see in the mean time im selling these bits - injector spacer - $150ish? - secondary fuel rail - 150ish? - meth tank, meth pump, nos solenoid blablabla all that random line and shit with it - 300ish? - my old surge tank setup with the pump - $300ish times are changing and so are the plans, could be starting with a D

hahahahhahahaha no i had no idea the centres had been flipped it's all good got bored the other night. Mine have had the same treatment Its an inch lower now with the wheels spaced out another inch or so hmmmmmm what to do

15x8's and 15x9's 4x114.3