crispymk2 Posted October 4, 2007 Share Posted October 4, 2007 I got a hole patched + rust done and powder coated for $80 a couple of years ago... cortina tanks are pretty basic tho. Quote Link to comment Share on other sites More sharing options...
peteretep Posted October 4, 2007 Share Posted October 4, 2007 what place do you get to do tanks etc? just a general engineer? Quote Link to comment Share on other sites More sharing options...
crispymk2 Posted October 4, 2007 Share Posted October 4, 2007 got mine done at a radiator and aircon place - Natrad... picked up next day, been sweet http://www.natrad.com.au/ might be a bit far away for you guys tho Quote Link to comment Share on other sites More sharing options...
NewGuy Posted October 4, 2007 Author Share Posted October 4, 2007 Well here is the new welded plate. Will primer and paint tonight also may drill the 1.5Inch hole i got to drill. Old Sender New Sender Mmmm Shiny New Gauge Looks Pretty much standard. Cheers To Hell I got to pick this sender and gauge for $35 Form Repco Quote Link to comment Share on other sites More sharing options...
Raizer Posted October 4, 2007 Share Posted October 4, 2007 Oh sweet, they had one in stock! Way better price than i got mine for too lol Quote Link to comment Share on other sites More sharing options...
NewGuy Posted October 4, 2007 Author Share Posted October 4, 2007 Oh sweet, they had one in stock! Way better price than i got mine for too lol Yea man i was stoked as. I got it all in tonight Took me bloody ages. Just wondering if your gauge goes up and downa little bit like it looses pwoer and then gets it again? Mynes like past the full mark doing that. Just wondering if i have something wrong. Common things anybody? Quote Link to comment Share on other sites More sharing options...
NewGuy Posted October 4, 2007 Author Share Posted October 4, 2007 Quote Link to comment Share on other sites More sharing options...
Requiemk Posted October 4, 2007 Share Posted October 4, 2007 Check your earths secure and good, did you grind/sand surface where you put it? Quote Link to comment Share on other sites More sharing options...
NewGuy Posted October 4, 2007 Author Share Posted October 4, 2007 Check your earths secure and good, did you grind/sand surface where you put it? I have a earth on the tank to a old earth and using some earth in the dash. i will redo both tomorrow. I was thinking that i had fucked it or something, i think i have had the same problem before with my Temp gauge. I will let you know. Cheer Boe Quote Link to comment Share on other sites More sharing options...
Raizer Posted October 4, 2007 Share Posted October 4, 2007 Just wondering if your gauge goes up and downa little bit like it looses pwoer and then gets it again?Mynes like past the full mark doing that. Just wondering if i have something wrong. Um i wouldn't know aye, my gauge is in the wardrobe in the spare room, and my tank/sender is in the shed at my sister in laws lol Quote Link to comment Share on other sites More sharing options...
NewGuy Posted October 4, 2007 Author Share Posted October 4, 2007 Lol Sweet as ill see how i get on with the ground thing., Quote Link to comment Share on other sites More sharing options...
NewGuy Posted October 5, 2007 Author Share Posted October 5, 2007 New ground on the grounds, new lugs and connectors everywhere, still got the problemo. Reading is now at about 3/4 to about half. Quote Link to comment Share on other sites More sharing options...
Requiemk Posted October 5, 2007 Share Posted October 5, 2007 go over all wiring look at all of your fuel sender wiring. Quote Link to comment Share on other sites More sharing options...
NewGuy Posted October 6, 2007 Author Share Posted October 6, 2007 go over all wiring look at all of your fuel sender wiring. What am i looking for? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.