Popular Post Taistorm Posted May 28, 2023 Popular Post Share Posted May 28, 2023 So I've been dormant for a little while with the old Mazda locked up at my parents place in NZ whilst we decided to shift back over to Perth to try and get ahead in life. Picked up an 08 wrx and ran around in that for a bit, sold it about 6 months ago and have been on the hunt for something old again for a bit of a project. Everything seems to get snapped up within hours over here and had missed out on an old TX Gemini, B310 Datsun, AE70 Corolla (amongst a few others) by a hair. Finally stumbled across this for a score from a Mitsi nutter looking to cull his fleet. It's a 1976 Chrysler-Mitsubishi Galant wagon. Believe it was a GL spec 1600 however it has had a 4g62 2000cc and 4 speed out of an l200 swapped into it. It's rough, needs work. Has rust (most of which is pretty minor bar the lower front guards and rear quarters) needs some leaks sorted out and the clutch looked, some electrical gremlins sorted out and then it should be ready for running over the pits to get licenced. Pretty stoked to say the least being in something oldschool again. Plans at this stage is to get it licenced and on the road properly, then thinking about engine swapping and cleaning it up a bit but we'll see what happens (we're trying to renovate our house at the same time and have 1.5yr old so it's just a matter of time and money freeing up). Here's some pics anyway. The arriving home off the tow truck. The boss definitely approves. Chur, Tai 41 1 Quote Link to comment Share on other sites More sharing options...
Popular Post Taistorm Posted June 18, 2023 Author Popular Post Share Posted June 18, 2023 Not a proper update but I have been trying to organise the shed a bit better and picked up some more tools to make my life working on this a bit easier. I'm in the process of changing jobs and my roll cab won't fit in the new work vehicle so now it will be staying at home. I've also picked up a Lincoln 191c multi process welder and a cheap jack and some axle stands (had to fix the family wagon a few weeks ago so got them then). I plan to weld up a solid steel work bench to take up half the back wall, setup a vice etc in the near future. More to do with mitsi, I've put some feelers out for parts and may have some better taillights and some interior bits sorted. Looking to get the front indicator lenses 3d printed as well. If I get time this week I'll take the welder for its maiden voyage and weld up the 2 piece exhaust. Cheers, Tai 12 Quote Link to comment Share on other sites More sharing options...
Taistorm Posted September 24, 2023 Author Share Posted September 24, 2023 Not a proper update as I haven't been up to much with this yet, have had a lot on and not much spare time. Have been trying to sort parts but really have no luck so far. A couple months ago I got a local exhaust shop to bend a bit of pipe and make a slip join to try marry the 1.6 exhaust to the 2.0 down pipe. The slip join cracked when stretching it out but it wasn't a problem to weld up. Pretty rough for now but should be ok. The exhaust gasket wasn't right and too small and I've had issues trying to find the right size. Also the first muffler was rusted out so I was gonna cut it out and just straight pipe it but I didn't have enough pipe at that stage. However I've since picked this up as it came up on sale... The boy wanted to sort out his bike first though. Must mean the engines coming out soon. Wonder what will be replacing it.... 6 Quote Link to comment Share on other sites More sharing options...
Taistorm Posted September 25, 2023 Author Share Posted September 25, 2023 After going to a local car meet Orient express yesterday (which was awesome with a huge turnout!) I decided to throw the exhaust manifold back on, hook up the battery and fire it up after sitting for a few months. Then today we had a public holiday so I decided to start pulling it apart and start the prep work for the new donk and assess the rust situation. I was gonna rip the engine out but it didn't have a front lifting eye and I didn't have anything to adapt to suit today so we'll leave it for now. However here's what I uncovered with the rust. Front of the lh sill. Battery box and where the inner tub meets the chassis rail. Rear corner infront of the firewall by the lh guard. Lh strut tower. The front of the chassis rails by the lower radiator support panel. Worse than I was hoping for but still manageable. Also had a few snapped bolts which was a pain in the ass. 5 Quote Link to comment Share on other sites More sharing options...
Popular Post Taistorm Posted September 25, 2023 Author Popular Post Share Posted September 25, 2023 Then after pulling off the wiper motor and having a look under the scuttle panel I found this! Was not happy at all... tbh I felt pretty defeated at this point. Was not keen at all to be needing to remove the windscreen and unpicking the scuttle panel to access this point. Thought about it for a moment then decided to start pulling the dash apart to see if I could access it from the inside. Still a prick to get to but I think I'll persevere with it. 14 Quote Link to comment Share on other sites More sharing options...
Popular Post Taistorm Posted December 23, 2023 Author Popular Post Share Posted December 23, 2023 Ordered an engine from a local importer months ago, was supposed to arrive late October but the importer had huge delays due to cyclones and customs and only finally had the parts ready for delivery earlier this week. Had a call yesterday saying the truck was on its way! What do we have here? It's a 6 bolt vr4 4g63. Imported over from Thailand with little to no information on it besides that it has done around 140,000kms and it drove about 400km to the place where the importer stripped the car down, also a short running video of it sounding OK. Looks like it has been sitting for a long time, signs of grey silicone all over it, wiring cracking in many places and pretty rough around the edges. Hoisted it into the shed and started stripping off the unnecessary shit today and have a look over it. Definitely lools like the head has been off at some stage and it's pretty clean under the rocker cover. I'm still unsure whether I'll keep this car and carry out the conversion but this arriving before Xmas has given me some motivation. Would be a weapon however if I pull it off. 12 Quote Link to comment Share on other sites More sharing options...
Taistorm Posted January 2 Author Share Posted January 2 Decided to do some more work on this on new years day. Wasn't sure on what spec the vr4 engine was so decided to see what we were dealing with. Was hoping it was a evo 0 engine so was looking for the tell tales nut unfortunately it fell short, no biggy though. ECI Multi on the intake didn't quite look right, turns out someone had just stuck a plate over the 'cyclone' lettering. Also the turbo is a td05h 14b, as opposed to the bigger 16g. Going off the ecu part number it looks to be from a 1988 vr4. Stripped off the bolt ons and had a look down the ports, no bad signs so far. Timing belt and idlers look to have been done but the water pump is pretty crusty on the inside. Decided to mock up the turbo flipped around for a laugh - Will probably just make up a basic log style manifold for this to keep costs down. Then ripped it off and put on some alloy tape to seal it up for now. Check out the repairs on this old manifold from previous cracks... Later on in the evening I decided to rip the 4g52 out from the bay. Got her all setup and on stands in the front so the engine crane would clear the lcas. Check out the inside of the bellhousing.. The bloke who swapped the 4g52 didn't sort out the right size clutch/flywheel setup and the outside of the clutch pressure plate has been wearing on the inside of the bellhousing - it hasn't driven really at all but when I brought it and test drove it around the parking lot I knew something wasn't right but didn't expect this haha. And here's where we're at. Does anyone know where I can source original plugs/connectors for the engine wiring loom, most of what's on here is old and brittle or broken and I'm keen to repair most of it or even maybe make a new loom entirely. Also if anyone has any suggestions for easy ways to go about the rwd swap please let me know. I have been reading up on project zero g and also a lot of online forums so far. I'll probably be looking at a top thermostat housing delete (to get better clearance at the rear) and run an inline thermostat housing. Have someone modify the inlet manifold to swap the tb to the opposite side. https://oldschool.co.nz/index.php?/topic/88881-tais-1976-galant-goon-discussion/ Chur. 9 Quote Link to comment Share on other sites More sharing options...
Popular Post Taistorm Posted January 2 Author Popular Post Share Posted January 2 Couldn't help myself.. The mounts off the 4g52 were pretty close so figured I'd just mock them up and and hoist it in to see how far off everything is. Mounts need to come up slightly to drop the engine a little and also shift about 20-30mm back. I'll probably chop up and modify the block mounts (or make new ones). And clearance at the firewall. Will need to reroute the brake line as it's too close to the cas and will need more clearance. Sump clearance. May need to trim the crossmember a little but might get away with it. I'll try get engine mounts sorted in the next couple weeks then there probably won't be any progress as our daughter is due in Feb. See how we go anyway. Chur 10 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.