WARTYM Posted January 13, 2008 Author Share Posted January 13, 2008 Intercooler Mocked Up Engine Shot Surge Tank Mock up Not yet ready to run hopefully this weekend all lines will be hooked up and radiator mounted to front grill Quote Link to comment Share on other sites More sharing options...
WARTYM Posted January 13, 2008 Author Share Posted January 13, 2008 START UP VIDEO: http://www.youtube.com/watch?v=lSxEQF4DkwM Sorry about the video & audio quality but did it with my smart phone 2mp so cant really expect much lol That run was without the radiator & instead to the intercooler we just hocked up the in and out of the engine with some thick pipe other wise it wouldn't start because it is factory intercooler & no exhuast we got the fuel lines all done went to repco to get about 10m of fuel line and for the efi fuel pipe they said $50 PER METRE that would come to about $500 asked if they had anything cheaper and just got normal fuel pipe not efi but he said it should hold very good, and $280 for new lead set decided not to get that as of yet and to shop around, facet fuel pump was $175, 4-7psi & 132litres/hour I love the sound of the turbos winding up when accelerating and turbo compressor surge when you decelerate seems like i might need a b.o.v cause the engine being generation 3 it runs 12psi boost Quote Link to comment Share on other sites More sharing options...
WARTYM Posted January 13, 2008 Author Share Posted January 13, 2008 It really does move with the new engine pushes me back into the seat will be putting boost up to 16psi for a quick run down the road (stock 12psi gen 3) but the small turbos cant really handle more then 16psi or eles they blow then maybe look at a single turbo conversion depends really Quote Link to comment Share on other sites More sharing options...
WARTYM Posted January 14, 2008 Author Share Posted January 14, 2008 More Rust Repair This is The Last Rust On The Jeep So Decided To Remove it and this is the other side which i am yet to patch up will be done tomorrow hopefully As the jeep sits in the shed also am painting and polishing a set of 15" rims plan on selling them cause i want wider and better looking but i suppose time pass lol before: After: Quote Link to comment Share on other sites More sharing options...
WARTYM Posted January 24, 2008 Author Share Posted January 24, 2008 got two rims polished and painted and one on the jeep to see what it will look like. and i think it looks madd height will drop a bit when let of the jack as the tyre was above the ground so i could slip my finger underneath the tyre Quote Link to comment Share on other sites More sharing options...
WARTYM Posted March 17, 2008 Author Share Posted March 17, 2008 Jeep was dropped off at import customs today for full panel and paint was mean as we cruised through huntly town with the jeep loaded on the trailer people were amazed. we had like 3 or 4 guys come up to us and tell us what a fucking mean project. Quote Link to comment Share on other sites More sharing options...
WARTYM Posted May 6, 2008 Author Share Posted May 6, 2008 lots of new parts from india, fucking blody hard to find, its all old new stock from all over india, dated back to the 60's & 70's Quote Link to comment Share on other sites More sharing options...
WARTYM Posted October 31, 2008 Author Share Posted October 31, 2008 been a long time since its been updates a few goodies first of all brought some 36x17x16 Racing drag slicks brought a set of 20x9 BSA mags with used 295/45/20 tyres also brought a set of brand new 295/50/20 tyres this is what the jeep looks like at the moment at the panel shop Quote Link to comment Share on other sites More sharing options...
WARTYM Posted April 6, 2009 Author Share Posted April 6, 2009 Long time no update so here we go.. intercooler mounted and piping all done Went for a cert in between Rear seat failed Need Lapbelts for rear seat Driveshaft Loop Wheels and Tyres to be confirmed Brakes To be rechecked once finshed And everything else passed Yay!! what it looks like now Quote Link to comment Share on other sites More sharing options...
WARTYM Posted August 22, 2009 Author Share Posted August 22, 2009 the where im up to now, havnt been using the interwebs much but im back on now Quote Link to comment Share on other sites More sharing options...
WARTYM Posted September 24, 2009 Author Share Posted September 24, 2009 thought i had blown the turbo and done some damage to the pistons, but all it was was that the flywheel had come loose haha, all fixed and the engine is back into the bay. got some new seats, what do you guys think ? whats your guys opinion on these seats ? i'll be getting the back retrimmed to match the front seats anyway... Quote Link to comment Share on other sites More sharing options...
WARTYM Posted September 25, 2009 Author Share Posted September 25, 2009 have just droped the setas off to get retrimed in a cream vinyl, including the front ones now what do you guys think, have the whole seat in a simple cream vinyl ? apply a orange piping around the outside of the seat like this: or apply a orange prping around the outside and inside where the material joins like this: the back seat will me in matching cream vinyl is well with the lines going down the middle like the front seats.... what do you guys think ? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.