-
Posts
10919 -
Joined
-
Last visited
-
Days Won
4
Posts posted by SOHC
-
-
I sold this to pay for the v8 rebuild but I had a go on a few of the later TS250s but I reckon the 185 ER is way better, if anyone has one of them they want to part with I would be keen.
-
your not tempted to get an aliexpress bigbore kit?
-
I have tried sliding doors and butterfly valves in home made mufflers with much disappointment, you may get a slight change but the baffle chamber of the bit of the muffler that has been bypassed still will still do its job if any part of it is open to the exhaust flow.
-
-
The 200 top end fits the 185
-
11 hours ago, nzstato said:
Pricing is model dependent...
'Good' condition ML7 with some tools ~$1k
Older ML4 or poor condition is few 100
ML7 with gearbox, or super7 2.5k + (though there have been a few sub 2k, bargains)
Mine had some tooling, I put it on Facebook and it was gone with in 16 mins. I dont like the bushes in the spindles, they are a pain in the arse
-
-
The price for myford lathes is crazy, I put mine here for $500 and no one took it
- 1
-
There are some B&S Facebook pages witch are good
- 1
-
10 hours ago, GregT said:
Yeah. There were only ever 2 or 3 SC's came to NZ. The guy in ChCh who owned one moved to West Australia and took his with him.
So is the WR based on the last of the air cooled YZ's ?
My friend got givenan SC500, its just sitting in the shed he hasn't even touched it, I would say the WR is basically an early YZ engine, it wouldn't need much improvement with its power, only 1000 were ever made but they seem to all be in NZ
-
8 minutes ago, GregT said:
Is that the enduro version of the SC500 ? The SC's make ridiculous amounts of torque - if you can master starting one.
The SC is the old 70s thing? I know where one of them is,the WR make over 60 HP
-
-
3 hours ago, GregT said:
Did you ùse the gn250 rotor and attach the hub from the aermacchi?
-
-
I got a stainless steel one, they say you can crank them straight in but it might pay to run a 12mm tap as far as i can
-
-
2 hours ago, NickJ said:
Yes I think so, i didn't get a good look at it, just put it on the trailer, the o e I got had legs but not sure if they were factory?
-
3 hours ago, nzstato said:
They must be rarer? Didnt know they did a 3 in 1. Those saw/planer combos turn up pretty regularly.
Pics?
I don't have any pictures, I was getting some tools from an old guy and he sed I could have it as it was going to the scrap and I sed I would find a home for it, it had the Tanner embossed spanner and the thing for doing the angels and stuff, he had got it new.
- 3
-
I got given a Tanner saw bench that has like a spindle molder on one end of it to, it came with all the attachments.
- 1
-
I had a sl 360 scrambler for a bit that did good wheel stands it had a sportster petrol tank and the exhaust had been made to look like a shotgun, but it broke a cam chain tensioner and i dumped it
-
-
52 minutes ago, GregT said:
And 10mm lift on the exhaust.....What timing does that give you ?
Lots of power,
- 2
-
Also the reed block I will chop out the divider and make a carbon fiber single petal
- 1
-
Discuss here about Yoeddynz's little Imp project...
in Project Discussion
Posted
Just have it as an empty chamber and it should sound like some kind of super car