Jump to content

4V Century V8 powered Dyna Camper Discussion


HumberSS

Recommended Posts

If you did want to talk to a truck person, some names I would suggest:

Dave Plum is a heavy vehicle certifier, and he will talk your ear off if you can get hold of him. 

Phil @ Waimea Engineering does lots of heavy vehicle fab stuff.

Either of those guys would have some ideas of practical ideas for how to modify the chassis.

  • Like 1
Link to comment
Share on other sites

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

34 minutes ago, anglia4 said:

If you did want to talk to a truck person, some names I would suggest:

Dave Plum is a heavy vehicle certifier, and he will talk your ear off if you can get hold of him. 

Phil @ Waimea Engineering does lots of heavy vehicle fab stuff.

Either of those guys would have some ideas of practical ideas for how to modify the chassis.

 

Our boy lives in Inglewood, so way closer to your neck of the woods....

  • Like 1
Link to comment
Share on other sites

I have a front cut off a 1995 Toyota dyna for cheap if you go down that Rd, had a 15b diesel in it, sounds like quite a lot of work this v8 engine would you be better off with a common Toyota diesel like a 1kz or 13b diesel? I’m sure the v8 would sound the goods though 

  • Like 1
Link to comment
Share on other sites

On 05/05/2022 at 23:30, shrike said:

Is the main issue that the carb fowls the cab in its current location?

My first thought is low profile efi conversion,  but I know you wanted to stay carbed. 

Anyway to remote mount the carb? Sounds like a good reason to go remote mounted turbo with a suck through carb ;)

How much dies the cab fowl on the carb/ top of the engine?

Could you raise that part of the seat/engine cover up?

Can you remove any material on the heads/cam covers to lower the engine more?

Sorry folks, been a few days away.

To answer this question, main issue is both fowling of cab and width between rails. Fowling of cab by a good 100-150mm. Im wanting to run a bench seat (had buckets, dont like the look). Main real issue though is the width for headers. not a lot we can remove off engine, but will shave a few bosses etc definitely.

Link to comment
Share on other sites

Re EFI, just not that keen tbh. I was born in 1981, TV was barely a thing. 

@anglia4 thanks I know Richard well.

@Otodat def not keen on a chassis swap. This is already more than enough of a job.

@MaxPower yeah its a lot of work, agreed 15B is the easier route. Im just attached to the V8 in this era Dyna as a combo. Im fairly irrational..

@CUL8R I still need primary tubes into some sort of collector, unless I run Zoomies through the rails, which sounds epic, but probably will weaken chassis a little too (although not was much as proposed.

Link to comment
Share on other sites

@ThePog you know you're a total cunt. But probably right. I have decided best 'first move' is to get rid of encumberances in the body, which need to happen anyway for trans clearance so there was no avoiding relieving the camper body anyway. May as well chop a hole, then see how much real clearance I have and if it truly is viable to slot it in there. Kyle reckons as soon as we clear the top, it wont take as much as I think to move it back/down and may in fact not have to move rearwards as far as it looks like it needs to. The only way to answer this question is with the chorus of the angle grinder.

 

  • Like 1
  • Thanks 1
Link to comment
Share on other sites

Not trying to be a dick and I do not intend to offend

But it seems like a lot of work to put a round peg in a square hole ,

and the round peg isn't very powerful, is hard to get parts for and needs some dickery to fit a trans to,

when you could do less work and put a better engine in it? 

Like you say, a SB chev would be smaller, a 302 would be even narrower, no efi, and you can get a 4 speed auto that bolts on 

 

Just my 2c feel free to tell me to mind my own business 

 

  • Like 2
  • Thanks 1
Link to comment
Share on other sites

On 09/05/2022 at 10:38, cletus said:

Not trying to be a dick and I do not intend to offend

But it seems like a lot of work to put a round peg in a square hole ,

and the round peg isn't very powerful, is hard to get parts for and needs some dickery to fit a trans to,

when you could do less work and put a better engine in it? 

Like you say, a SB chev would be smaller, a 302 would be even narrower, no efi, and you can get a 4 speed auto that bolts on 

 

Just my 2c feel free to tell me to mind my own business 

 

Bro fully appreciate the input, no offence taken.. Will consider further.. May still pursue irrational option.

  • Like 1
Link to comment
Share on other sites

Height is the kicker for exhaust can you raise the engine enough so your have the exhaust ports above chassis without driveshaft angles getting horrible?

If so adapt a sidedraft carby like a dellorto to keep it under the seat, no huge mods then to chassis. Please run 4" side pipes like a 70's panel (porno) van. You can always swap out the Toyota with a Real mopar Hemi later.

 

 

 

Or fit a smaller engine like the more  compact big block chev. 

 

Link to comment
Share on other sites

  • 2 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...