Jump to content

VK304’s sr20det 88 vanette


Vk304

Recommended Posts

  • Replies 178
  • Created
  • Last Reply

Top Posters In This Topic

  • Vk304

    179

Top Posters In This Topic

Then It got technical pretty quick, i wanted to find out if the wheelbase and the mounts (engine/box) would be the same as in the donor van... but after looking at the crossmembers, and the differences. No. 

Also found the subframe had 25mm spacers to lower the engine to make it fit under the covers (sr is a lot taller than the a15 or 2litre that they had) --note in the picture they have inserts welded in the spacer, so it can't crush when you tighten the bolts, a cert requirement--- as well as quality bolts with washers and spring washers, the right size for the bolt! 

Simple fix right? Swap the donor Van's crossmember with the new van..

So I put the spacers and the other crossmember in ( my goal was to keep the seats- covers- seatbelts all factory so the cert guy can't give me grief about any of that! 

Well after swapping some bushings around so it had nice bushings and cleaning the grease off, I put it in the van ready to accept the engine....

20200912_111056.jpg

20200912_115612.jpg

20200912_123310.jpg

20200912_123254.jpg

  • Like 3
Link to comment
Share on other sites

A lot of problems . .. .

The van I got was not the same, it's a different engine bay ,I had to remove the intake and cut the van :/--temporarily I swear! just to seat the engine, well the mounts were on a bad angle, the engine was on a bad angle just to fit... no go ,too bad , back to drawing board! 

20200912_142127.jpg

20200912_143432.jpg

20200919_140944.jpg

20201004_115526.jpg

20200919_141014.jpg

20200912_161516.jpg

  • Like 7
Link to comment
Share on other sites

So I decided to start with moving the engine forward, and down, I tried to use the s15 mounts but they were big and chunky and were going to hit the turbo if I moved the engine where i wanted it... 

Thinking that if I got some smaller diameter mounts and the tallest possible to get close to the 70mm or so the sr mounts were I'd have something close to working, there were other considerations such as not lowering the engine too much and risk the sump becoming one with the road, or hitting the crossmember and the angle it would be when resting under the engine cover lip. In other words it was faking tight.

I had a look at the mount shop website and found some BMW mounts that were the right diameter, but a bit short maybe ... nothing some spacers wouldn't fix, but turns out I diddnt need spacers and after hacking some prototype engine mounts together it fits good .

 

Screenshot_20201103-185041_Chrome.jpg

20201011_105909.jpg

20201004_115429.jpg

20201026_154151.jpg

20201025_102630.jpg

20201024_155936.jpg

20201026_154157.jpg

  • Like 3
Link to comment
Share on other sites

Nice and level, next up it was time to mock up the gearbox, I wasn't crawling under the van with that filthy thing so couple cans of degreaser and a water blast it came out better than I thought it would.

Put it on without clutch or anything.

All I had to do was slot the mount Holes a little and it fit right up for now...

20201025_121441.jpg

20201026_112551.jpg

20201026_112558.jpg

20201026_114954.jpg

20201026_122114.jpg

20201026_153956.jpg

20201026_153951.jpg

  • Like 3
Link to comment
Share on other sites

Aaand more previous f-ups come to haunt me, the driveshaft was 25mm too short , note the white marker on it, a cert fail, it was like this in the other van too and its symptoms were vibrating under load and a yoke that showed signs of wear due to excess play, and so now I had to fix this... new driveshaft?

20201026_132224.jpg

20201026_132221.jpg

20201026_153304.jpg

  • Like 4
Link to comment
Share on other sites

Working on the intake problem has been a challenge, to start I would have kept the original one but it's just not possible.

It too tall and I would have to modify the seat and seatbelt anchoring, not keen on that at all, so my second option was buy a aftermarket short runner one, but this van is going to be using all factory ecu turbo etc. I would lose a lot of torque across the low-mid range rpm, besides that may not fit either due to the engines proximity to the 'firewall' . 

Well I can weld aluminium, so I'd make an intake to suit my needs .

Keeping the runners as long as I could fit was the goal

 

20200912_163331.jpg

20200912_162309.jpg

20201011_105927.jpg

20200912_152222.jpg

  • Like 4
Link to comment
Share on other sites

Soo I sold the old 'a15' and gearbox, but its come back, me and the buyer overlooked the code on the block, it's a a12 with a a15 head :(, i diddnt know that was a thing but so it is, so it will be up for sale again, it does have an exedy clutch and pressure plate which looks in great condition.  . . 

20201107_172313.jpg

  • Like 1
  • Sad 1
Link to comment
Share on other sites

And a whole lot of mock-up, mounting radiator, routing intercooler pipes, and general placement to see if it all will fit, and so it does, still have a bunch of brackets to make which will take a bit of time such as intercooler mounting in front of radiator, radiator bottom mounting, air intake mount finalizing, engine mount finalizing, driveshaft hoop, weld back engine bay,  and my most non favorite task- running wiring !

20201107_180013.jpg

20201107_175610.jpg

20201107_175534.jpg

  • Like 5
Link to comment
Share on other sites

Well the drivers seats had it, I just noticed some suspect welding when I was moving it and well it got worse the more I looked at it, more shitty workmanship, and only one bolt holding the rail on, as in one bolt holding the seat in the car when you bolt the rail down! 

The other side has a sliding piece of angle? Safe ???? , time to find another seat I think.

I could weld this and reinforce it etc but the seat covers blown out too, hope someone's got a 80s van seat lying around 

20201111_193604.jpg

20201111_193640.jpg

20201111_193812.jpg

20201111_193708.jpg

20201111_194727.jpg

20201111_194707.jpg

  • Like 1
  • Confused 2
  • Sad 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...