Jump to content

Welder buying spam


kws
 Share

Recommended Posts

22 hours ago, kws said:

Im going to try pick up a bottle of gas from bunnings this weekend, are there any special requirements for transporting it? I figure it probably shouldnt be rolling about in the boot?

Also. If you’re not a trade (trade pass card) customer you’ll have to try and click and collect. Only trade customers allowed inside and , in silverdale at least, only allowed in half the store. 

  • Like 1
Link to comment
Share on other sites

  • 2 weeks later...
  • Replies 356
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Owner cylinders can still work out ok depending on gas usage / type. I get mine tested every 5 years for around $100 with a fill of CO2. At my current usage rate that will last till next test. Might have to read back a few pages, but I think the Bunnings deal is pretty sweet. BOC took the piss on pricing for years so i'd personally never use them. Their pricing is why I purchased a cylinder to start with, no regerts.

Link to comment
Share on other sites

Hello welders,

TIG filler rods.

What type and diameter would I need for the following:

  • Mild steel exhausts, panel steel and motorbike frames. BOC seems to only offer 1.6 and 2.4mm diameter. 1.6 fine for what I need?
  • Stainless exhausts (is this usually 304?)

Hearts

 

Where is the best place to get this from online?

 

Link to comment
Share on other sites

1 hour ago, Goat said:

Hello welders,

TIG filler rods.

What type and diameter would I need for the following:

  • Mild steel exhausts, panel steel and motorbike frames. BOC seems to only offer 1.6 and 2.4mm diameter. 1.6 fine for what I need?
  • Stainless exhausts (is this usually 304?)

Hearts

 

Where is the best place to get this from online?

 

I got my tig stuff from these guys, just because it's all online. https://www.prolineindustrial.co.nz/cat/welding-equipment/tig-welding/tig-filler-wires

I am still a novice, but I used 1.6mm for my mild steel exhaust. It went okay, you have to be really crazy with cleaning the weld area, any trace of oil or dirt and the weld fills with bubbles then you have to grind out and start again.

  • Like 1
Link to comment
Share on other sites

Agree with KPR, 1.6 mild steel is the general rod

For stainless most of what I do is fine pipe work so I use a 1.2mm give a real tight weld. 

Have 2.4mm mild steel as a back up for big gap craft jobs or things requiring filling up. 

Stainless rod on mild steel is a good get out of jail card, its probably naughty but it welds yucky mild steel without going all poopy. Good if you are repairing old exhausts etc.

Really like the silicone bronze rods, makes pretty welds.

  • Like 2
Link to comment
Share on other sites

On 24/09/2021 at 20:11, westy said:

Threw one in the back seat today. He had to leave it outside for me to pick up cause he couldn’t bring it inside for some reason. 

Finally managed to get to bunnings today, only to find that Porirua has no full bottles of MIG gas, havent for weeks and have no ETA for more. I did grab a regulator, some 0.6 wire and a couple of extra cut off disks though. Apparently Petone has some bottles, so will give them a try.

  • Like 1
Link to comment
Share on other sites

5 hours ago, Geophy said:

Agree with KPR, 1.6 mild steel is the general rod

For stainless most of what I do is fine pipe work so I use a 1.2mm give a real tight weld. 

Have 2.4mm mild steel as a back up for big gap craft jobs or things requiring filling up. 

Stainless rod on mild steel is a good get out of jail card, its probably naughty but it welds yucky mild steel without going all poopy. Good if you are repairing old exhausts etc.

Really like the silicone bronze rods, makes pretty welds.

I know many pro welders that use a dab of stainless when shit gets bubbly.. never even seen a failure coz of it. 

Never used silicone bronze but looks so damn nice.

You'd like stainless stick welding. Super easy and it comes out delicious looking 

  • Like 3
Link to comment
Share on other sites

7 hours ago, flyingbrick said:

 

You'd like stainless stick welding. Super easy and it comes out delicious looking 

Yea just mash it in there and it looks like a pro did it..

 

+1 for a bit of ss wire on some crusty mild.

Also, like sheepers said, dont need a foot pedal. Just set the downslope and when things start getting a bit spicy, let off the trigger and back on before it shuts off. Couple of them to get you out of trouble and youre away again 

  • Like 1
Link to comment
Share on other sites

10 hours ago, flyingbrick said:

I know many pro welders that use a dab of stainless when shit gets bubbly.. never even seen a failure coz of it. 

 

I must get some stainless rod and try this! I assume that unless you are welding safety critical parts for NDT, it won't matter using a bit of stainless?

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...