Jusepy82 Posted July 7, 2018 Author Share Posted July 7, 2018 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted July 7, 2018 Author Share Posted July 7, 2018 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted July 7, 2018 Author Share Posted July 7, 2018 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted July 7, 2018 Author Share Posted July 7, 2018 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted July 7, 2018 Author Share Posted July 7, 2018 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted July 7, 2018 Author Share Posted July 7, 2018 During the week or next weekend I shall take off the panel completely. I am going to tackle the dodgy repair in the driver side sill soon as well. Thanks for reading be back soon ta. Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted July 7, 2018 Author Share Posted July 7, 2018 Here is my discussion forum cheers. 1 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 4, 2022 Author Share Posted November 4, 2022 Hello again friends , here's the eskie in fine form 1 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 4, 2022 Author Share Posted November 4, 2022 Wow , so it's been a long time yeah ! Sooooo I brought myself a welder to finally start on my escort again ! I've become motivated again and have started working on the pannel van again. Tonight I spent a long time making a patch for the left hand side inner wing pannel. I enjoyed it too be honest and not putting any pressure on myself to get it done... no rush = good job ! Anyways here's some pics ! 7 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 4, 2022 Author Share Posted November 4, 2022 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 4, 2022 Author Share Posted November 4, 2022 1 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 4, 2022 Author Share Posted November 4, 2022 6 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 4, 2022 Author Share Posted November 4, 2022 I shall weld in the patch to the inner wing this weekend , super excited how it turned out. 1 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 4, 2022 Author Share Posted November 4, 2022 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 5, 2022 Author Share Posted November 5, 2022 Welllllll now , not the post I wanted to post. Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 5, 2022 Author Share Posted November 5, 2022 Welllllll, I tacked it in nicely.. Started welding it in in different spots as per normal. Turned down the welder abit as as blowing holes left right and center... oops too cold now... finished it up and ground back the welds wayyyyy to far. Rookie mistake now metal way too thin and holes appearing. Time to take a step back and reevaluate what I'm up too. Fucked it up completely , had a bourban and a couple of beers to drown my sorrows. Look at it again in the morning and figure out what im going to do... #weldingnotaseasyasIthought. FUCK 3 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 5, 2022 Author Share Posted November 5, 2022 I need alot more practice with adjusting the welding settings . I'm too embarrassed to put the final product up here. I thought I had it sussed but turns out I was full of shit , pretty gutted to be honest but as the wife put it ... were u expecting it to go super smooth ? Back to the drawing board.. 1 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 6, 2022 Author Share Posted November 6, 2022 Here is the pictures promised. Thoughts and suggestions lads ..thanks 1 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 20, 2022 Author Share Posted November 20, 2022 Soooooo today I decided to tackle this pannel again. I cut out the offending pannel and started making the replacement replacement pannel . Here's a couple of pics , I brought a few new tools to help me be a better pannel maker. A comma beating dolly and a flat pannel beater hammer! Thanks for reading 6 1 Quote Link to comment Share on other sites More sharing options...
Jusepy82 Posted November 26, 2022 Author Share Posted November 26, 2022 Right so tonight I decided to weld in my panel. I havent ground it bk yet but I'm pretty happy with it inside and out ! I've been practicing my welding abit durning the week. Not the best but way better than the last attempt. 4 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.