DB8-TypeR Posted June 12, 2019 Author Share Posted June 12, 2019 So my engine turned up from Japan last week, assembled it all on Sunday and last night acheived its first start 7 Quote Link to comment Share on other sites More sharing options...
Ash-he Posted June 12, 2019 Share Posted June 12, 2019 Oh that gauge cluster is so lush! Very jealous Quote Link to comment Share on other sites More sharing options...
DB8-TypeR Posted June 12, 2019 Author Share Posted June 12, 2019 Yea, the Dash is pretty much what made me want this. And it even all works! Quote Link to comment Share on other sites More sharing options...
DB8-TypeR Posted June 14, 2019 Author Share Posted June 14, 2019 Finished assembly and took it for its maiden voyage around the block. Acceleration is pretty average but once it gets into top gear it goes pretty good. Need to adjust idle as once warm it wants to stall 8 Quote Link to comment Share on other sites More sharing options...
DB8-TypeR Posted August 19, 2019 Author Share Posted August 19, 2019 Finally got the Chaly running with new exhaust/carb/head Had got sidetracked when I only noticed one of the intake manifold threads was stripped after I swapped the head. So then ordered some threaded inserts off aliexpress that were M6 inner thread and M9 outer. Then once i had everything attached it just wouldnt start, no compression..... checked all the headgasket and things Id done and couldnt fault it but when kicking it over it would just chuff air and fuel back out the carb. Did some thinking and decided to check valve clearences (which id set before I put the head on) and dontcha know it, the intake valve was tight as. Loosened it up a bit and first kick it started. So now its running and have ridden it around the driveway, need to order some jets of ali to get it right, idle jet seems a bit big and a unknown size, main jet is a 75 at the moment which shouldnt be far off. Have been using the spacy as my daily for the last 7 weeks or so (probably should register it...) and apart from blocking the carb a couple times it been good. Quite fun to ride and offers a bit more wind protection on the cold mornings than the DJ1 ever did. Hopefully be able to commit some finances to getting the Dax finished by the end of the year 7 Quote Link to comment Share on other sites More sharing options...
DB8-TypeR Posted October 12, 2019 Author Share Posted October 12, 2019 Still using the Spacy as a daily (still not registered.....) and have got the Chaly running pretty good, 38 idle Jet, 82main and the needle one clip up from the bottom. Apart from being a bit obnoxiously loud its pretty good. And into the Dax, got a new seat and exhaust from webike, discarded the muffler that came with that and attached a Supertrapp Replica from aliexpress. Also have a 120/90-10 tyre on the back to check it was all going to fit. Chain will be a tight fit but hopefully ok 2 Quote Link to comment Share on other sites More sharing options...
chees- Posted October 13, 2019 Share Posted October 13, 2019 On 27/05/2019 at 12:47, datlow said: will that be the ride height? reckon it would look sweet/impractical(would it even turn?) lowered 2 2 Quote Link to comment Share on other sites More sharing options...
DB8-TypeR Posted October 14, 2019 Author Share Posted October 14, 2019 Am still working on lowering it (too many projects), wont be that low so I can retain some ridability but will see what I can do. It developed a knocking sound from possibly the gear train today so hopefully nothing serious 1 Quote Link to comment Share on other sites More sharing options...
DB8-TypeR Posted October 30, 2019 Author Share Posted October 30, 2019 Thanks to @Raizer I got some Honda Gyro front shocks (already shorter than spacy by 10mm) then shortened the shock a further 20mm. At this stage I havnt cut the spring, its just got more preload to make it stiffer. The rear still isnt lowered (apart from when I sit on it), but need to sort out a kick stand instead of center stand as it drags a bit much even at this height. Once Ive sorted that then should be able to get it a bit lower Pic from previous page for reference Other than that, still just using it daily to get to work and its going sweet. Knocking sound from previous post was loose bolts holding center of the rear wheels to the rim 8 Quote Link to comment Share on other sites More sharing options...
DB8-TypeR Posted November 30, 2019 Author Share Posted November 30, 2019 So a Dax update, have been slowly accumulating parts and then stripped it right down, got some more cracks in the frame welded up and began the painting process. Conveniently I was working night shift (no one else in the workshop) and we have a large oven that is meant for baking varnish onto electric motors Left it to sit for a while then started making it look like a bike again Still a long way to go, lots of little jobs like tidying up the original badges 7 Quote Link to comment Share on other sites More sharing options...
Popular Post DB8-TypeR Posted December 7, 2019 Author Popular Post Share Posted December 7, 2019 Two tyres the same size make a good bit of difference 16 1 Quote Link to comment Share on other sites More sharing options...
jerald Posted February 2, 2023 Share Posted February 2, 2023 On 28/07/2017 at 11:25, chees- said: Yea fair enough, they look fucking good with max slam on 8" wheels. Cant quite get the same look with the dio sadly. still keen to swap wheels! Oki Hey mate,do still have this af18? Message me if you still have this one 0272724976. Im really interested if you are going to sell this. Anywhere here in nz 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.