Nominal Posted November 10, 2020 Share Posted November 10, 2020 Bargain! 1 Quote Link to comment Share on other sites More sharing options...
tortron Posted November 10, 2020 Share Posted November 10, 2020 morrie club? set a peanutbutter jar over the end with a hole in the bottom. collect oil in a pan, pour it back in when finished 2 2 Quote Link to comment Share on other sites More sharing options...
AllTorque Posted November 10, 2020 Share Posted November 10, 2020 Rubber glove and electrical tape works too. I have seen those trans plugs in nz before, just can’t remember where. Quote Link to comment Share on other sites More sharing options...
AllTorque Posted November 10, 2020 Share Posted November 10, 2020 https://www.qualitytools.co.nz/transmission-fluid-retaining-tool-p-6557.html  https://www.waihyd.co.nz/toledo-automatic-transmission-fluid-retaining-tool-1363669  https://www.supercheapauto.co.nz/p/toledo-toledo-transmission-fluid-retaining-tool/SPO1352687.html Quote Link to comment Share on other sites More sharing options...
Nominal Posted November 10, 2020 Share Posted November 10, 2020 11 minutes ago, AllTorque said: https://www.qualitytools.co.nz/transmission-fluid-retaining-tool-p-6557.html  https://www.waihyd.co.nz/toledo-automatic-transmission-fluid-retaining-tool-1363669  https://www.supercheapauto.co.nz/p/toledo-toledo-transmission-fluid-retaining-tool/SPO1352687.html Thanks Rogee, name is the key, Do you reckon they would work when the engine is going and tranny is in Park?  Quote Link to comment Share on other sites More sharing options...
AllTorque Posted November 10, 2020 Share Posted November 10, 2020 As long as the output shaft isn’t spinning it will be fine. Fluid level may not be that high anyway. What about trans cooler lines? Are you going to loop it? Does the starter bolt to the trans? Quote Link to comment Share on other sites More sharing options...
Nominal Posted November 10, 2020 Share Posted November 10, 2020 3 minutes ago, AllTorque said: As long as the output shaft isn’t spinning it will be fine. Fluid level may not be that high anyway. What about trans cooler lines? Are you going to loop it? Does the starter bolt to the trans? Yeah, I'll just clamp a bit of hose on the cooler ports Need to block the speedo drive hole (as I found out last night while lifting it) 5 1 Quote Link to comment Share on other sites More sharing options...
yoeddynz Posted November 14, 2020 Share Posted November 14, 2020 You've built your Morris v8 subframe and mounts already. I'm impressed! Some black paint and you're done. 4 1 Quote Link to comment Share on other sites More sharing options...
SOHC Posted November 14, 2020 Share Posted November 14, 2020 On 10/11/2020 at 19:24, Nominal said: Bargain! Apco has F type fluid and it’s a fraction of the price than anywhere 1 Quote Link to comment Share on other sites More sharing options...
SOHC Posted November 14, 2020 Share Posted November 14, 2020 Is that a Hydromatic or a C4? Quote Link to comment Share on other sites More sharing options...
Nominal Posted November 14, 2020 Share Posted November 14, 2020 31 minutes ago, SOHC said: Is that a Hydromatic or a C4? C4. Quote Link to comment Share on other sites More sharing options...
ajg193 Posted November 16, 2020 Share Posted November 16, 2020 Anyone else notice up to 10% difference in fuel consumption between chipseal and asphalt road surface? Could be a good way to get a nice virtual Dyno boost @Roman 2 Quote Link to comment Share on other sites More sharing options...
Roman Posted November 16, 2020 Author Share Posted November 16, 2020 10% is quite a bit of difference It's easy to test though, do some coast down tests in neutral and look at decel rate on both surfaces Quote Link to comment Share on other sites More sharing options...
ajg193 Posted November 16, 2020 Share Posted November 16, 2020 Here is some data for a Volvo (brick): I feel like for something significantly more aerodynamic the fuel consumption numbers would be affected far more by surface roughness Max difference at each speed for that graph: 50 km/h : 3.6% 60 km/h : 7.2% 70 km/h :Â 7.6% Â Â Â Quote Link to comment Share on other sites More sharing options...
ajg193 Posted November 16, 2020 Share Posted November 16, 2020 https://eapa.org/wp-content/uploads/2018/07/fuel_efficiency_report.pdf Quote Link to comment Share on other sites More sharing options...
Yowzer Posted November 16, 2020 Share Posted November 16, 2020 Run bigger tyres. Problem solved. Quote Link to comment Share on other sites More sharing options...
ajg193 Posted November 16, 2020 Share Posted November 16, 2020 Talking about tyres, I'm gonna get a new set on the Starlet today. Out with the fantastic Yoko A539s and in with hopefully good Falken 912s Quote Link to comment Share on other sites More sharing options...
Carsnz123 Posted November 17, 2020 Share Posted November 17, 2020 How anal does one need to get as far as tyres go on a street car? like as long as they don't slip in the wet like Super Meows or are noisy and mushy like Hiflys, you're golden. 1 Quote Link to comment Share on other sites More sharing options...
tortron Posted November 17, 2020 Share Posted November 17, 2020 have to buy the good tyres and brake pads for the wife, holy shit shes terrifying on (and off) the road  good tyres are cheaper than a new car  had to get decent tyres for the ute cos it kept doing skids and drifts Quote Link to comment Share on other sites More sharing options...
Yowzer Posted November 17, 2020 Share Posted November 17, 2020 RE003s on everything 4 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.