RUNAMUCK Posted July 13, 2020 Share Posted July 13, 2020 9 hours ago, NickJ said: Ah, now those pages make sense, I was expecting something on the lines of "if rego/wof expires between A and B, the new expiry date is C" Will throw new rego on and give them a good warm up/run Report back if it still.lets you do it. I rego'd a project over lockdown. Quote Link to comment Share on other sites More sharing options...
NickJ Posted July 13, 2020 Share Posted July 13, 2020 1 minute ago, RUNAMUCK said: Report back if it still.lets you do it. I rego'd a project over lockdown. System will allow me to rego the cars, just wanting to fully understand what is legal before risking fines I can't afford! Quote Link to comment Share on other sites More sharing options...
Nominal Posted July 13, 2020 Share Posted July 13, 2020 Just now, NickJ said: System will allow me to rego the cars, just wanting to fully understand what is legal before risking fines I can't afford! Also https://thespinoff.co.nz/money/26-06-2020/the-cops-wont-ping-you-for-an-expired-wof-but-your-insurance-might/ Quote Link to comment Share on other sites More sharing options...
tortron Posted July 13, 2020 Share Posted July 13, 2020 yes but not expired "extended" Quote Link to comment Share on other sites More sharing options...
Raizer Posted July 23, 2020 Share Posted July 23, 2020 On 09/12/2019 at 21:10, kws said: If anyone is after a cost effective Dial Gauge, I picked one of these up today and its shockingly decent for the price. Has a certificate of NZ calibration, and has a decent heft to it, doesnt look or feel cheap. https://www.saecowilson.co.nz/#/Product/info/M339A Same with the magnetic base, better built than the price lets on https://www.saecowilson.co.nz/#/Product/info/M329 These are $36inc each at Trade Zone ATM, picked them up this morning. 2 1 Quote Link to comment Share on other sites More sharing options...
igor Posted July 26, 2020 Share Posted July 26, 2020 Calling all knowledgeable electrical persons. I'm looking for a replacement bulb for a stage floodlight. Looks like a seven inch sealed beam headlight but it isn't. It's 240 volt. Coreys in Balclutha have told me that these are extinct because they tried to get some for someone else and couldn't. Do any of you wonderful people know where I might find one please? Quote Link to comment Share on other sites More sharing options...
tortron Posted July 26, 2020 Share Posted July 26, 2020 Search for 240v sealed beam https://www.lamps-on-line.com/sealed-beam-lamp-240v-300w-par56-wfl-gx16d.html 1 1 Quote Link to comment Share on other sites More sharing options...
kyteler Posted July 26, 2020 Share Posted July 26, 2020 Wait. Are you telling me you can use the internet searching facility to find things that you know the parameters of? Weird. I thought you had to ask people everything. Thanks, tortoise. 4 Quote Link to comment Share on other sites More sharing options...
tortron Posted July 26, 2020 Share Posted July 26, 2020 my suggestion would be to tell coreys to get fucked so over guys in various business saying stuff doesnt exist, just say you dont have it in your books and to look elsewhere your results may vary 3 1 Quote Link to comment Share on other sites More sharing options...
Bling Posted July 26, 2020 Share Posted July 26, 2020 Can use YouShop for UK stuff, as they'll likely not send direct. Quote Link to comment Share on other sites More sharing options...
tortron Posted July 26, 2020 Share Posted July 26, 2020 That was literally the first hit to come up, there's prob some in NZ or easy to get Quote Link to comment Share on other sites More sharing options...
UTERUS Posted July 26, 2020 Share Posted July 26, 2020 https://lmgtfy.com/?q=300w+par56 Quote Link to comment Share on other sites More sharing options...
h4nd Posted July 26, 2020 Share Posted July 26, 2020 site:.nz 300w par56 Quote Link to comment Share on other sites More sharing options...
igor Posted July 26, 2020 Share Posted July 26, 2020 Thanks guys. Potentially found in Tauranga. Quote Link to comment Share on other sites More sharing options...
tortron Posted July 31, 2020 Share Posted July 31, 2020 recommended powdercoaters in Auckland? making some steel doors Quote Link to comment Share on other sites More sharing options...
peteretep Posted July 31, 2020 Share Posted July 31, 2020 We use spraywell at work. Apparently the trick to getting a better price is to go around the back on the left hand side and find the younger dude (son). The dad charges more. Also the charge prices seem to come out their bums, they just pick a number. Good quality finish though 2 Quote Link to comment Share on other sites More sharing options...
ajg193 Posted August 12, 2020 Share Posted August 12, 2020 Surface finish on reground cams - how smooth should they be? The one I just got ground looks like it has a pretty rough surface, especially around the base circle - even some voids in the casting. Will the cam polish itself up as it gets bedded in? Quote Link to comment Share on other sites More sharing options...
UTERUS Posted August 12, 2020 Share Posted August 12, 2020 @BobbyBreeze is the cam guy Quote Link to comment Share on other sites More sharing options...
BobbyBreeze Posted August 12, 2020 Share Posted August 12, 2020 12 hours ago, ajg193 said: Surface finish on reground cams - how smooth should they be? The one I just got ground looks like it has a pretty rough surface, especially around the base circle - even some voids in the casting. Will the cam polish itself up as it gets bedded in? They should be smooth, shiny almost polished finish off the grinder, like ~15RA surface roughness. If they are rough then they will eat the lifter for sure. Have you got any photos? Sounds like maybe the grinder operator didn't do a very nice finishing dress on the wheel. 1 Quote Link to comment Share on other sites More sharing options...
ajg193 Posted August 13, 2020 Share Posted August 13, 2020 12 hours ago, BobbyBreeze said: They should be smooth, shiny almost polished finish off the grinder, like ~15RA surface roughness. If they are rough then they will eat the lifter for sure. Have you got any photos? Sounds like maybe the grinder operator didn't do a very nice finishing dress on the wheel. You can see the lines that go all the way around the lobe, it feels like a pretty roughly turned surface. 1 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.