buzzy Posted November 13, 2013 Share Posted November 13, 2013 here are a couple pic's of the sedan slowly getting bits and pieces done on it, //oldschool.co.nz/index.php?/topic/41145-buzzys-b110/ 6 Quote Link to comment Share on other sites More sharing options...
Popular Post buzzy Posted November 13, 2013 Author Popular Post Share Posted November 13, 2013 camber plates in 14 Quote Link to comment Share on other sites More sharing options...
buzzy Posted February 20, 2014 Author Share Posted February 20, 2014 Slowly getting things done, Oil cooler lines made up and test fitted, Have radiator getting welded up then can make up the hoses for that. Once that is done I can pull the engine out for a rebuild and get the engine bay tided up, get all the non needed bit cut of and hole welded/filled up. 4 Quote Link to comment Share on other sites More sharing options...
buzzy Posted March 1, 2014 Author Share Posted March 1, 2014 rad hoses made up.Will sort out hose clamps, then can make a start on the fuel system Quote Link to comment Share on other sites More sharing options...
buzzy Posted March 15, 2014 Author Share Posted March 15, 2014 Stormy weather = stay inside so made the most of being able to get out in the shed. new fan in place, close fit but will be ok if I use the flush type cap screws. //oldschool.co.nz/index.php?/topic/41145-buzzys-b110/ 1 Quote Link to comment Share on other sites More sharing options...
buzzy Posted March 18, 2014 Author Share Posted March 18, 2014 pushed it outside for a wash. Pic for motivation! 7 Quote Link to comment Share on other sites More sharing options...
buzzy Posted April 5, 2014 Author Share Posted April 5, 2014 Slowly making progress. Just waiting for the fuel tank to come back from having a AN fitting installed then can run the main fuel line and install the fuel pump. 1 Quote Link to comment Share on other sites More sharing options...
buzzy Posted May 17, 2014 Author Share Posted May 17, 2014 Slowly getting more done on the old girl. Swapped my wheels over to get the ones I had on it polished. Car is now at engineers getting the trans tunnel made up, then exhaust. Once that is done it will be off to get the engine wired up //oldschool.co.nz/index.php?/topic/41145-buzzys-b110/ more progress soon 2 Quote Link to comment Share on other sites More sharing options...
buzzy Posted June 9, 2014 Author Share Posted June 9, 2014 Got the car at engineers. Brought a rx8 6-speed for it so will get that mounted up and the gearbox tunnel made up, then I can get the exhaust made up. Brought some different wheels for it too.. hopefully they fit??? //oldschool.co.nz/index.php?/topic/41145-buzzys-b110/ 3 Quote Link to comment Share on other sites More sharing options...
buzzy Posted July 4, 2014 Author Share Posted July 4, 2014 Went and had a look at the old girl today.. 6 speed is in. Just needs tunnel made up which should be happening next week! 1 Quote Link to comment Share on other sites More sharing options...
buzzy Posted July 23, 2014 Author Share Posted July 23, 2014 3 Quote Link to comment Share on other sites More sharing options...
buzzy Posted July 24, 2014 Author Share Posted July 24, 2014 6 Quote Link to comment Share on other sites More sharing options...
buzzy Posted August 1, 2014 Author Share Posted August 1, 2014 Tunnel's all done. got the sedan back home now to get the drive shaft made up then can go back for exhaust. 5 Quote Link to comment Share on other sites More sharing options...
buzzy Posted May 31, 2015 Author Share Posted May 31, 2015 Finally done something on the sedan after it just sitting there for awhile. managed to get the rear sitting about right. Ute diff is off getting mounts made up then can put that in. Once diff is in, then I can sort d/shaft. Should slowly have more progress on this. 9 Quote Link to comment Share on other sites More sharing options...
buzzy Posted August 1, 2015 Author Share Posted August 1, 2015 Ute diff is now in. Drive shaft getting made over the next couple of weeks. Will start the search for a fuel cell, then look at getting the engine rebuilt! 8 Quote Link to comment Share on other sites More sharing options...
buzzy Posted August 23, 2015 Author Share Posted August 23, 2015 progress 7 Quote Link to comment Share on other sites More sharing options...
buzzy Posted March 12, 2016 Author Share Posted March 12, 2016 Slowly chipping away at this. Drive shaft now made. Engine bay almost ready to paint. got a pair of seats, will get them re-covered sometime. 9 Quote Link to comment Share on other sites More sharing options...
buzzy Posted April 23, 2016 Author Share Posted April 23, 2016 . 9 Quote Link to comment Share on other sites More sharing options...
Popular Post buzzy Posted May 30, 2016 Author Popular Post Share Posted May 30, 2016 slowly going back together 14 Quote Link to comment Share on other sites More sharing options...
buzzy Posted August 5, 2016 Author Share Posted August 5, 2016 Engine is now being rebuilt, Hopefully not to far away now! 2 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.