MACKAZ Posted August 29, 2016 Author Share Posted August 29, 2016 Thread dredge. Have found a major balls up, pedal box is too high on firewall, by 85mm at least. I thought I'd be able to sneakily extend the pedal, but it will be outside the 1:7 measurement to be legal. Oh well where's the grinder?? 1 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted August 29, 2016 Author Share Posted August 29, 2016 Oh that's right, I've positely identified the rear section, and it's also 20s but later. It's 27-29 Essex! Yet another weird piece of antiquity.... 1 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted March 1, 2018 Author Share Posted March 1, 2018 Haven't been around for a while. Work/life epically busy but I am back into it again. I fucked up due to lifting the cowl up. So what goes up must go down. Chop up the cowl and reinforcing and lower the pedalbox and steering column. Pics or it didn't happen Made a purchase of 50x50x3,more 25x25x3 box,100x3 and 50x3 flatbar today. About to start the seat and seatbelt anchorages (the tricky shit). I've given up on the idea of back seats, just way too much political shit to deal with, damn you lvvta.... 8 1 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted March 9, 2018 Author Share Posted March 9, 2018 Removed the master cylinder and booster and mocked up just the pedalbox and column. Made me a little bracket out of 3mm plate and bored it out to suit the steering column shaft Then migged it into place and gave it a grind up I'm about to take the whole lot out and make the patch to cover this whacking hole. Over and out. Lost pics. 1 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted March 11, 2018 Author Share Posted March 11, 2018 Immediately after my last post i fabbed this patch and I've just finished welding it in. Gotta bore the holes now, that's gonna be fun Oh and I'll grind this shitty looking welds into shitty looking lumps, remember my pledge of no bog? Still stands (unless cert jerk has an issue with it) Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted March 14, 2018 Author Share Posted March 14, 2018 In typical MACKAZ fashion, another pictureless update. But I was listening to as spot of Motorhead on my way home, and a song Jailbait come on. Freaking awesome song and I think quite a fitting name for my rod. 2 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted March 17, 2018 Author Share Posted March 17, 2018 Cut the holes out, flipping mission of a job, but got a result. Lost pics 5 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted March 21, 2018 Author Share Posted March 21, 2018 Blank canvas all cleaned up. Let's build a seat!!!! 2 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted April 6, 2018 Author Share Posted April 6, 2018 Another pictureless update. Thought before I get àll skippy and build a seat I'd better check with lvvta the best way to proceed. As stated before the 4 seat idea has gone. Have had lengthy forum discussion as what this is classed as, and it is classed as scratch built. So I'm going to put 4 point harnesses in it, which means it requires headrests and apertures for the belts to go through. High back bench seat design is commencing....feel free to throw up ideas in the discussion thread if you got ideas, I'm struggling......cheers 1 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted April 21, 2018 Author Share Posted April 21, 2018 Swap meet purchases today, 39-47 Hillman guards, and pair of straight Buckeye bumpers, ones missing the centre bracket. $120 the lot, stoked! 5 1 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted September 2, 2018 Author Share Posted September 2, 2018 Hopefully getting a repower very soon to something waaaay cooler, waaaay more powerful and quite a bit bigger displacement. Watch this space, gotta go pick this piece of pure awesome up...... Cue mysterious music 7 Quote Link to comment Share on other sites More sharing options...
Popular Post MACKAZ Posted March 16, 2019 Author Popular Post Share Posted March 16, 2019 Engines aren't here yet, but a pile of bits are. New engine to be fitted is a 265 Hemi Valiant. 200hp standard vs Holdens 92hp will propel this pile of parts much quicker. 14 1 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted April 29, 2019 Author Share Posted April 29, 2019 Went to Whangarei swap meet. Came back empty handed. Anyways plans for the Hemi are 6 straight pipes, necked down to 3/4 inch 19mm at the ends to shut her up. Also looking at making a "high-rise" inlet manifold from exhaust tubing and a lump of 75x50mm boxsection, topped with a trio of Holden single barrel carbs. Also on the cards a third pedal MIGHT possibly get squeezed in the footwell 7 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted August 5, 2019 Author Share Posted August 5, 2019 Another typical MACKAZ pictureless update. Been put on hold again so I can get my house completely finished off. I'm gonna have a go at fitting a Holden MC6 "Torquemaster" 4 speed gearbox behind the Hemi. Workmate and I intend to strip the box down, cut the belhousing casting away, then Mill the front flat and build an adapter plate to mate it to the Valiant bellhousing. Am I mad? Yep. For added wank factor it's the same gear pattern as an original Chrysler 4 speed I had in my Charger, to the left and up 3 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted August 5, 2019 Author Share Posted August 5, 2019 Discussion here https://oldschool.co.nz/index.php?/topic/29542-mackazs-22-buick-rat/ Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted October 29, 2019 Author Share Posted October 29, 2019 Well, I've gotta wait a little longer. Sharn goes storage barn is on one side of a creek opposite to the entry. Guys recently had a flood go through his farm and its washed the culvert out. And guess what's on the barn side of the creek? The dudes digger, with only one track on it. And the other tracks this side. Bah, might be easier to try buy a 265..... 1 Quote Link to comment Share on other sites More sharing options...
flyingbrick Posted October 30, 2019 Share Posted October 30, 2019 should just get lots of chain/cable and drag the tracks across to the digger. that or use hot air balloons. 1 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted October 30, 2019 Author Share Posted October 30, 2019 Lol 54 come alongs... From memory it's a fair hike up to the shed too. Last time I bought a 720 King cab off him, I got another 4 720s in bits. When he Barry collects he does it to the extreme 2 Quote Link to comment Share on other sites More sharing options...
MACKAZ Posted June 20, 2020 Author Share Posted June 20, 2020 As mentioned in spam I'm tired of waiting. Thanks to old mate @rb drifter we are off to collect a specimen tomorrow. Certainly not Hemi cool, but I think what I have in mind for this should get the forums approval. Pictures tomorrow...... 5 1 Quote Link to comment Share on other sites More sharing options...
Popular Post MACKAZ Posted June 22, 2020 Author Popular Post Share Posted June 22, 2020 Here it it. 4.0l SOHC Falcon out of a AU3. Done a Derby. $50 Special. Also have a dirty Holley 4bbl and a turbo off something to go along with it. Have manual bellhousing and 3 speed up it's bum. 15 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.