Popular Post Truenotch Posted October 17 Author Popular Post Posted October 17 Had my first go at laying carbon fibre today. Decided to do a straight wet layup because 1. It seems easier than bac bagging and 2. My foam core would need reinforcing to withstand a vac bag. This way will be a bit heavier and possibly be a bit looser without the compression of a vac bag, but I'm OK with that. I'm using vinyl ester resin which goes off a lot quicker than epoxy, so it shoild be dry and read to do the underside tomorrow. I think there's a couple of voids around the front lip (it's kinda intricate and was hard to and keep it stuck). We'll find out how it went in the morning! 18 1 Quote
Popular Post Truenotch Posted October 18 Author Popular Post Posted October 18 Side one turned out pretty good. Gave it a trim and sat it in the sun this morning: Side two looked more simple, but actually worked to a little trickier and we were left with a couple of lifted areas on the sides of the tunnels. I'm not too stressed about it for now, but will possibly cut those sections out and re-laminate later. You can see the raised parts here. Maybe they'll act as little air fences to keep the flow in the tunnel? 😄 The surface finish is a raw carbon weave texture, so it'll need another layer of resin and a flat/polish after trimming. I'm pretty happy with it for a first carbon project... it's definitely ambitious for a newb 😅 17 1 Quote
Popular Post Truenotch Posted October 19 Author Popular Post Posted October 19 Gave it a quick trim and This is how it came out. It still needs a final gloss layer on the underside and lip section to get it smooth, and a couple of sections need patching. A peep at one of the tunnels from the inside: Learnings so far are that I think I could use a lot less resin. We loaded up the final layer to try and make it glossy, but I've since realised that you need to wait for it to cure before adding the gloss coat. It's super rigid through the middle too! Shouldn't need too many mounting points to make it solid. 28 Quote
Popular Post Truenotch Posted November 2 Author Popular Post Posted November 2 Got the splitter mounted. I'm still amazed that these Integra mounts work so well. They angle outwards a bit (because my chassis rails have some toe out... Not sure if it's factory), but they still slot in and out for quick removal and installation. Also added a couple of extra supports to give it some load bearing ability. Then it was off to Levels for round 2 of SS cup. I managed 9 laps in qualifying before struggling to select 5th gear. Dropping the oil revealed a couple of selector detent bearings and a bunch of other swarf. But as we all know, Timaru is a bustling automotive metropolis, so I jumped on Marketplace and organised a gearbox to be DoorDashed out to the racetrack: I missed both races while we got the box swapped that afternoon. Had it ready to race in the morning, lined up on the grid and.... Broke my diff before the first corner 🫠 To quote Mark who took this shot "It's lucky you can't hear the photo... Because it sounded like a skeleton having a wank in a biscuit tin". I'd patched together both the gearbox and the diff last year using minimal parts and tbh, I'm surprised they lasted this long. The crown wheel and pinion has been in the car since @mark105's dad installed it in 2013 and I gave it a good cook up while learning how to rebuild it last year by doing it wrong the first time. I have a brand new CWP set in stock, so will get that installed and go racing again in November. 27 Quote
Popular Post Truenotch Posted Saturday at 01:28 Author Popular Post Posted Saturday at 01:28 Pulled the diff the other night and assessed the damage. The pinion had worn down to sharp edges and probably reached the stage where it damaged the crownwheel. One tooth will have broken, then a few others followed suit. This was starting to happen when I rebuilt it last year and it handled the whole season of racing, plus a bit more. I'd say the initial damage pulled the hardening off the gears and it's been at the mercy of the gods since then. Kinda impressed it lasted this long tbh! The solid spacer took a beating and is stuck to the bearing. Apparently if the shims are too thin this can happen, so maybe it lost pinion preload and got worse from there? Hard to say: Here's how the pinion should look: So I've pulled it apart and dropped the lot off at Gearhead Diffs for a rebuild. I had a full Weir Performance 5.13 ratio crown wheel and pinion set in stock with bearings, new spacers, pinion shim kit etc. Hopefully the 5.13 isn't too short... I intended to install this along with my high RPM engine later on, but the racing gods have forced it to happen sooner 😅. It should be good for Levels and Highlands... maybe Ruapuna too, but could run out of gears at Teretonga. We'll find out soon enough! 14 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.