Leaderboard

Because everyone likes laughing at my misfortune, let's have another look at those big-end bearings. Yeah. The crank was also scored seven ways from Sunday, and the machinists next door were reluctant to skim it, so now it's a big ole paperweight. These were the worst ones but pretty much every single journal was rooted. We did work out the root cause of all this pain - the factory oil pump had eaten itself, apparently a common thing with the 1st gen motors. I never realized the 4A-GE also suffered from this weak point - it's a common thing to occur on the old Mazda B6Ts as well, although those tend to blow the relief valve and spring first. Lots of deep scoring against the cover: Take note of the area around the vivid mark: In the meantime, things got busy... and my wallet got empty. We acquired a donor 4A-GZE bottom end (from an AE101 this time) and Karl attempted to make a good one out of two. The end result: my block, pistons and sump + donor crank and rods = this. He also sourced a brand new oil pump from Toyota and a couple of other bits and pieces. Head has been sent for a skim, as there was a 0.004" bow in the face (eek). Toyota purists may note the AE101 4A-GZE rods are actually weaker than the preceding AW11/AE92 4A-GZE rods, but I was assured that for my application it wouldn't make a shred of difference. Different story if I was planning to go 7A and/or turbo I suppose. The first photo below should answer the age-old question of whether 1st gen 4A-GZE (AW11) blocks were 7-rib or 3-rib. Generic oil filter for the running in period. Better get more than 100,000km out of this shiny new TGP pump! Thanks to fellow oldschool member @Dell'orto I now have a SC12 from an AE101. They look very similar at first glance to the one that came off the AW11 but note the radius of each pulley face; AE101's is slightly smaller. If this translates into a slight boost increase, it won't be a bad thing I'm sure. When I next go back to the workshop I'll dig the verniers out and compare the inner diameter of each pulley, but I'm pretty confident they are different sizes, and the Toyota wizards on the internet also seem to indicate the same. This clutch also arrived. Sadly, Toyota no longer stocks a genuine clutch kit for the AW11 SC Next step is to speak to Mark at Toyota to see if I can find a suitable 1.1mm or thicker MLS head gasket before the engine can be fully reassembled. And do some more overtime in the mines to pay for all this faffing about. Discuss the colossal fail here: //oldschool.co.nz/index.php?/topic/49412-80s-kid-part-ii-eds-aw11-sc-chit-chat/

As much as I love my wheels tyre rub is an issue since lowering. I am running 175/50's but rubbing with any weight in the boot or back seat. I took a chance last Sunday evening and pilled the kids in the back to go for a short drive, turned out it was a real short drive. Sidewall wore right through within 4km then the tyre popped. Long story short I want to get some new wheels that suit my lifestyle better, 13x7.5 -19 offset is just to aggresive and tyre options are a bitch. I am probably going to get some new repro Hotwires in 13x7 +3 offset. Until then I have borrowed some old 13x6Cheviot Hustlers. They have seen some life and been on many a car and stored for years so are a bit rough. Spent a few hours today cleaning them up, pretty pleased with how they have turned out. Will put my tyres on them tomorrow, buy some new shank wheel nuts and then do some driving.

And adult supervision arrived and advised me that the exhaust also needs to be detached haha, thanks Al! Nek minute

Brought home 2 trailer loads of death/Honda/toys today, with the reputation that at least one of them has, I may have found exactly how I am going to die haha 1st off the one that's supposedly too dangerous to ride 1985(?) Honda ATC125m trike, looks mostly complete, told it was running a while ago, but the gearbox mucks around and it's got no brakes, will try and get it going tomorrow. That frame thing in the corner of the trailer is a home built/modded go kart He's dropping the axle and bearing blocks etc off next week. 2nd trailer is where it gets a bit more fun in my mind 1990 Honda Gyro X, 49cc with the correct amount of strokes, looks like it was regged as a motorcycle rather than a moped, so hopefully I can get it on a moped rego!! Also to share the death, Aaron got a Honda powered kart out of the deal Carb clean, oil and fresh gas and away it went! Clutch slips a lot though and I need to find a brake disk for it as well as get the caliper mount welded back to the frame, he's very impressed with it though lol He got a bit braver after a while. Gyro only needed fresh gas and a jump start to get going, so we gave it a half ass wash and I took off on it, got 5k from home when it died and then would only run at less than 1/4 throttle, managed to ride it home feathering the throttle at a blistering 7kph. Quick squirt of carb cleaner and it was away again, it's a fucking hoot to ride, tops out at 45 but shit it feels like it's flying and yeah I think I'm in love. Got several thumbs up from random people too haha. Shit I hope I can get it on moped reg!!! If I can't it'll be a tidy up and on sell Otherwise I'm thinking 70cc kit, big carb, custom pipe, 12x10 or 10x8 ATV rims from eBay with stretched scooter tyres on the back, 10" or 12" Dio front end with disk brake etc, the stock 8" front 6" rear wheels with tiny drums leave a lot to be desired! Something like these but rougher and cheaper

Whatever you do, don't try to rationalise any of this. I can hear everybody saying 'why would you bother?' already. About 12 months ago I was clawing my eyes out one weekend, I needed a hobby. Preferably one that could be done on the lounge coffee table as I really don't have the space for a complete vehicle (which is a bit of a laugh as I've since purchased an old car that bit of work but that is a story for another day). Anyway I was scrolling trademe one night an saw this old wooden ski boat for sale, I fizzed. I looked at that listing at least 23 times over the coming days. The lines of it were similar to an old, cheaper Chris Craft (if you don't know what a Chris Craft is do a google search and try not to drool on your keyboard). I didn't buy that boat, someone else made the terrible life decision and spent $2500 on it. But all along I thought 'man it would be cool with a V12 Jaguar engine in it'. Now this isn't a project of how a V12 Jaguar engine gets turned into a coffee table, well, not yet at least. I starting doing various googlings of V12 Jaguar motors and thought they looked cool with Weber IDFs on them. more googling said that 40mm Weber IDFs were the size of choice (don't ask me why, it just seemed to be the most common size). Trademe searching continues. One day a 40mm Weber IDF appears on trademe, perfect I think, I can pull it apart, clean it and put it back together on a coffee table (the whole plan of a hobby to begin with). The carb is in Christchurch, Runamuck is a champion and puts it in a box and sends it to me, Ka pai. I pull this thing apart, glass bead bast it at a buddys place and put it back together with a new throttle shaft, bearings and gaskets purchased off Ebay. All along wondering why it looked different to other 40mm IDFs on google images. More research ensues and it turns out it is a model unique to the Fiat 124 (I think the 124 Spyder specifically) and would have been one of a matched pair. Anyway I now have this tidy looking carb. Awesome, now what?

I had a pretty productive week on the prince. Made it to the auckland OS auckland monthly without a hitch. It was a good night! I managed to get some stop leak into the radiator and so far so good hasnt leaked any since the initial leak. Mean. Another problem which has been occuring is after driving the starter motor doesnt seem to want to tick over. Can hear the solanoid tick but nothing from the starter.. So yesterday i decided to take it off and inspect it. On inspection it all looked OK. Was full of oil/grease due to rocker cover gasket leaking oil all over it. Gave it a good degrease and clean up, re greased what needed to be done. It was auctually prick of a job. I needed to remove intake manifold and extractors to get the starter motor out. Mish. Anyway once back together i turned it on and off about was 10x total in between of letting it get to temperature. Took it for a drive around the block turned off and on no problems. Boy was i wrong. I went to put some gas in and got stuck! Same problem ticking away. While i had to sit there for 40 odd minutes until the car cooled so it would start again i read after market extractors causing issues run to close to block and ofcourse.. the starter motor. I felt the starter motor and it did feel hot. It has a remote solonoid on the guard so it cant be that.. or can it. Needed a push start to get home from mates after gas station break down and this morning i could not get it going again. Maybe the battery is stuffed.. it is a 2nd hand one i brought from zebra 2 odd years ago. Apon stumbling on an old barry and engaging conversation he had a piece of heat shield from ACL which he gave me to wrap starter motor in to hopefully stop the issue with the starter. Battery currently on the trickle charge. Tomorrow i will do some more tests once i grab my multimeter from work. On another note caught up with Rich and got this sweet roof rack off him Had a siezed clamp which abit of heat. Multi grips and WD40 it was free pretty easy. Here's some pics. I'm abit 50/50 with it at the moment. Lets see if it grows on me. Crappy driveway photos couldnt move car. Tell me what ya reckon Discussion:

The only suspension on the ATC is the balloon tyres and the seat foam!

Tested out the route. Route is awesome. Heaps of variety with mean bends and downhills, views and short cuts. Queen St traffic light drags are gonna be the highlight of the day. Can't wait for the 27th. Gotta get the bike tip top now. Less than a month to go! Trailer skids also awesome. Ft: @Shakotom

Almost finished the aluminium work now.

Except for the hand brake cable which decided to snap when i parked up at home. British cars know how to celebrate getting a warrant.

I haven't looked too closely, but I think this one has the high/low selector at least, and a big spring holding the shifter up. It's tomorrow's mission. Looks like I can get a pair of second hand 10x9" alloy wheels for $250 delivered, tyres are going to be the hard part I think. That's a 10x9 with a 205/30/10 on the left, looks perfect to me. /Should get it legal before even thinking about wheels/pipe/stretch.

Now, Will it fit? Well, by crikey, it might just work... Of course it's all good having one side line up, the real test is when #2 is made and whether or not it will simultaneously line up. On the desk it looks plausible. And with some minor filing of the holes on the cylinder head flanges (I haven't fixed the spacing issue with the stud holes) they even fit on the head, with the ID on the intake runner being on the money with the intake port on the cylinder head. It all looks plausible, but just to be sure I drop some bolts of conveniently the right diameter through the holes to see if they line up. Magic, The butterflies open like they should and it appears the intake runner and bottom of the carb line up as they should, not bad for a rookie if I do say so myself.

While that is going on, a couple of months back another weirdo (I say weirdo because you have to be to own one of these things) lists a V12 Jaguar engine for sale here on Oldschool. On this particular night I'm 3 or 4 Coronas deep, which to me is the perfect amount to assist in making rash decisions without worrying about the consequences. So I message the guy and say I'll take it, and fire some money away. Oh man, It's in Dannevirke. How is this going to work, luckily a buddy was going to a wedding down Wellington ways and picked it up for me on the way back, I then picked it up from his place in the Waikato. It is a Pre HE motor, out of a Series 2 XJ12 sedan according to the block number, The internet led me to believe the Pre HE motors are the ones to get when it comes to these motors, which was it's big selling point. I made a day trip to pick it up and got it back to Auckland and on an engine stand, I swear it was the worlds longest day

Couple of nice lil pictures from the since non-stop driving Hasn't missed a beat

@Raizer Gyro scene wasn't that massive that I knew of but I do know where you can get the decent wheels, wide and crazy. Search for the name on the 2 right pictures below on Facebook. He's a Filipino dude shacked up with a Thai bird. Ships world wide and speaks English. Worth a shot.

Sweet whip man. I'm gonna say nay to the roofrack, maybe something lower profile with some curves but with such sweet styling already I wouldn't run one unless I was using it to cart something.

Ed, as your self-appointed financial adviser, I strongly suggest you invest in those cams.

Set of 193b's sitting in my wardrobe doing nothing at all that would surely be lush.

More jobs done. This random looking combo will turn into a duct to feed the air box. It will get cheese cloth draped over it to make a shape like this, then will be coated with resin and chop strand to create the part. Then it'll fit here with a short length of 6" hose and a flange on the air box inlet. Did a bit more folding too. The radiator and inlet ducting it almost finished. Still needs the endplate done for the filter end. Gave it a test fit with the guards on. Still need to trim the new part on the bonnet.

I cannot put into words, how jaulous I am of your trinkets.

Bead blasting things yourself is all well and good, but you need an air compressor that can keep up and it can take a bit of time. I saw a guy (Brent) advertising his vapour blasting business on here and thought I'd give that a go. and I tell you what, it's the way to go, paying someone to clean up your mess is just so easy. So the two shitty carbs got his treatment, you can see the before and after here. This has presented a problem though, as the Carb I originally bead blasted myself has a slightly duller finish than the Vapour basted ones, so it will be coming apart tomorrow to get vapour basted, hopefully it comes out looking similar. Kind of hard to tell the differnet in the photo of all 3 lined up, the one on the right being #1, It is duller than the other 2 in person Anyway, If you have grubby stuff that you don't want grubby anymore, I 100% recommend throwing it at Brent http://vapourblastingnz.co.nz/

cool, I'll carry on then. So CAD is a prick of a thing if you are a hobbyist, everyone wants $4.2 million for a licence for a legitimate copy of some software. I was watching a youtube video by ICON 4x4 (go check them out, they build some fancy FJ40s) where he mentioned a free CAD software called Fusion 360, I did a google then downloaded it. Since then I've started to dabble in working out how to use it, which for someone who has no prior knowledge in design work is a bit of a learning curve, Youtube videos to the rescue. After much mincing about I managed to draw a thing, well, a series of things, taking the measurements off one of the intake port gaskets. This is where I need to make honorary mention of Ned, he has the ability to make your drawing turn into an actual thing. I send him a copy of the file and the next day I get a text saying he has some things for me. 3D Printed out of PLA, whatever that is, some kind of plastic. If that isn't amazing enough, lo and behold, the things fit. The stud holes aren't quite in the right place, they're a couple of mm to close to each other, nothing a quick file can't fix though. The other flange shown above lined up perfectly with the bottom of the Weber. At this point I think I am the bees knees.

Can a Jag V12 fit on your coffee table while still leaving room for the coffee?

Overdue an update! Wasn't happy with the engine mount setup I had. The A-series to K-series mount adaptors I got came with some rubber mounts that were gradually deforming just having had the weight of the engine on them, not even put any torque through them yet. Grabbed some Landy v8 ones from ebay as they were the same depth but much more solid, see?; Next on the list was brakes. Car should have a decent amount of go, so wanted some stop to match. Plumped for the MRP kit http://www.mrpltd.co.nz/product/kp61-starlet-big-brake-kit/ rather than faff around with building something up myself, the KP has a weird system where an offset disk bolts to the back of the hub, bugger mucking about with that. Plus these are pimppppp; Old: New: Only pain with them is I specifically ordered a setup to fit behind 13" wheels and they don't fit behind my 13" wheels. The WORKs have an indented lip on the inside barrel that interferes with the caliper. Got some 25mm bolt on spacers to help with clearance, but definitely going to need some serious arch tickling with them on. Problem for future me. One job I've been putting off for ages is finishing the dash wiring. Bit the bullet today and sorted it; Now have working oil pressure warning light, charge light, and check engine light. Pleased. Hate getting my head around this sort of thing - ended up bringing in a fused common 12v IGN feed to the back of the gauge to run the new circuits through, since they use a switched earth to complete the light circuit rather than the common earth arrangement that the stock starlet dash uses. I've got a nice custom 10k RPM tacho setup coming that will also tee off of that IGN, so saved myself some work there too. Left on the to-do list in my head: -Wire in new tacho when it arrives -Finish fan switch setup (waiting on a part), fit rad and fans back in, fill with coolant -Fill and bleed brakes -Gearbox and diff oil -Fit spacers and front wheels, roll arches -Clean and refit interior -Refit front panels and fender mirrors -Check all suspension and brake bolts are tight ..think that's about it? Sweet

you're a pretty cool dad!

Started tinkering again the other night checking everything again when i discovered abit of moisture inside the dizzy cap and also inside the dizzy was pretty dirty n scummy so i gave it a good clean started her up.. the good news is i think that may have been the problem? I a made sure everything was plugged in properly in regards to the wiring n plugs. Unfortunately when testing the radiator must have sprung a leak and water started to appear squirting out of radiator bummer! But i guess atleast its good it happened now than when im driving down unaware! Buggar. Apparently it wasn't so great in traffic anyway. I had a quote of 650 odd dollars for a re core so looks like ill be going alloy which is alot cheaper. I won some pretty sweet retro carpet so went down to tauranga and picked it up In the end i decided to carpet the floor and ceiling for that blast from the past luxurious lounge spec cruising. I rather like it. Step into my office Discuss. //oldschool.co.nz/index.php?/topic/36619-daves-prince-b200/

Banter here, //oldschool.co.nz/index.php?/topic/54510-kelvins-1985-rover-sd1-banter/ Hi everyone. Long time reader, first time poster. I have this thread posted on a couple of others, and thought it might be of interest to some members here. This thread will begin at the start, way back in.... November, last year and end at current day. So, about 10 years ago I had an SD1, an 85 Vanden Plas EFI in Cashmere Gold. Sadly i sold it because i couldnt afford to run it as my daily back then, and have regretted selling it since. Anyway, yesterday i picked the new toy up. Its a 1985 Rover SD1 Vanden Plas EFI (again), but in Zircon Blue. It needs some love, but its got good bones. It runs and drives, and actually drives really well. The powerhouse So the plan is to give it a really good tidy up, get it in as good condition as i can, but also build a new engine wiring harness and install my Speeduino ECU. Early next year i intend to use the car as my wedding car, so the clock is ticking! Theres more info on the car on my website too. http://www.tasteslikepetrol.net/cars/rover-sd1-two/

Sweet trike. My parents have an even older version where the rims and tyres are one piece. Think about 4 inch rims with really big balloons moulded onto them. Rode it all the time when we were kids and noone died or even got hurt. It floated too so was fun in the creek Just googled and found out what it is. I must go save it now

Not sure about that particular roof rack, looks mighty tall. On your starter issues, have you tried giving it a good clout when it refuses to turn over? Sometimes the brushes can stick in the holders. A bash can make them spring into place again. You probably tried this already but I thought it would be worth mentioning.

And 0.7mm trd headgasket.

Jag V12 was designed to handle 8000rpm with 4 valve heads, iirc 2 valve heads max out at about 7000rpm.

Any reason you don't go the easier route with 3 sets of 4AGE Quads? 1.6L x 3 is 4.8L and I can't imagine a V12 pulling 8000rpm like a 4AGE so there should be more than enough airflow for a 5.3L V12? Plus 6 sets of side/down draughts, even just finding shitty bodies to start with, is going to cost like 400 times the amount of 3 sets of quads. But I do applaud what you are doing. @Goat may have some tips as he toyed with his V12 and a Link a long time ago.

Took it to east tamaki for a ride around to run it in a bit Now does 71kph flat out. Hopefully the new rollers turn up this week and that should make it accelerate better-it kind of goes good at first, then bogs down while the cvt changes ratio, then accelerates again once it can gain rpm again Also it's a bit Harley Davidson in the corners, doesn't take much for the exhaust/ side stand to touch down

That is such a fantastic collection of death machines, how do you even come across a load like that?

MRP stroker kit

I'd be lying if I said I haven't :-). If i put my feet on the bumper and push pedals with my hands...oh and look so cool at the same time, it can be done :-).

Video of you driving?

x2, It looks heaps better now

Progress! Pulled this be front off the car and removed radiator ect to clear up some space. Have unhooked everything on the motor (I think) so it's pretty much ready to pull out. Have removed alternator, intake and a/c since the photo. Might wait for adult supervision to pull the motor out.

And after a bit of tinkering, replaced the dud coil... and boom! Hell yeah, so then I employed a human test pilot to act as a crash test dummy So: far more work than anticipated, way more money than I should've...but priceless, watching your kid drive a toy you've made yourself.

wheels and lows make it look so much betterer.

Got a new car for work to replace the wagon which was getting a bit tired. I told my boss it needed a headlight bulb and a couple of other small things and by the end of the discussion we were looking for a new car I figured I didn't really need a wagon so that made choices a bit easier, I like falcons despite the issues I've had with the wagon, they are big comfortable things that go ok and are pretty cheap, and don't cost much to fix when they do have dramas. When I got the wagon it had already done 240ish kms so I wanted something with more life in it, I looked at a couple of xr6 s but this one was similar money with 125kms and a bit newer, it's an xt which is the basic spec but it was always going to get the wheels off the wagon and some springs anyway so I did that today. Much betterer

Preview vid from the CRC Speedshow. My little beut is at about 1:15 on:

It gets from A to B Dirt masters training after work around red rocks, good fun it was!!!!

Hope this car is still running and the new owners are treating it well such a nice car

Hah turns out it was already a 70cc and the new piston makes it 84cc, not 100 cc as advertised I see why people mess around with scooters, had it stripped in 30 min. Found some grey paint that matched ok so painted the bits of frame that were modified The variator rollers were worn with big flat spots so hopefully the new ones make that work better .

It’s been a bit of a rough weekend, so what better cure than to take the Rover out for a spin and an Italian Tune-up. The sun was out, so off came the car cover, and out came the Rover. I had been meaning to check out the new Kapiti Expressway that has just been built, but hadn’t had a chance to make it up that way, and every time I wanted to drive the Rover recently the weather has turned to mud, and what fun is it cruising in the pouring down rain? Not to mention not being able to button her back up again after the drive due to the car being wet, and then getting covered in pine needles. So yeah, this was an adventurous trip. In my whole time with the Rover, I have never driven it this far from home. The furthest is usually to either Upper Hutt or the CBD, roughly 20-30km away. The Rover has been running well recently, and after the water pump failure it’s been holding its fluids and been mechanically sound. A pleasure to drive. Firing the car up for the first time in a couple of weeks, it didn’t start quite as sweetly as usual, and was running a bit lumpy and spluttering when given gas. Obviously not happy with the tweaks I did last time (in an effort to make warm starting easier), so I tapped a few keys on the laptop and reverted back to a previous tune. Started and idled much better this time. The first test was the new Haywards Interchange, which is an utter clusterfark, no matter which way you try to go through there the road markings are a mess and everything is guided by some messy cones. It will be good once it’s done, but blegh. Once the temporary 50kph zone changes to 100kph though, it was time to unleash all 190hp, and the sound of my people. Pedal to the floor, trans kicks down and off we go in a roar of V8 anger. She may not be fast, but it hardly matters with a sound like that. It was a fairly slow drive around SH58 thanks to a typical Prius driver which couldn’t hold more speed than a 30 year old Rover through the corners. Oh well, more time to enjoy the cruise and the scenery. The rest of the drive was pretty uneventful, other than seeing a sweet steam train choo chooing its way to Pram. Lots of railfans hanging around taking photos of it. Probably got some with a Rover photobombing them, lol. The Kapiti Expressway is a new 18km long grade separated four lane expressway built to bypass a rubbish bit of roading that used to go through a couple of towns and slow everything down. This is only one section in a bigger project, which will include the Transmission Gully Expressway that will take traffic off the two lane coastal route between Porirua and Paraparaumu (Kapiti), but the Kapiti Expressway is the first section to be completed and drivable. Gives an idea of what the rest of the project will be like. Four lanes good. Heading to Paraparaumu for lunch, we took the exit that said “Paraparaumu”, as expected, and strangely got shunted straight off the new expressway and back onto the old State Highway. Not the glamorous expressway I expected! Stopped at BurgerFuel for lunch, snapped a sneaky bum shot After lunch we found a proper on ramp to the expressway and decided to head North. Not knowing how far the expressway went, we just cruised along until the new road ran out, and we were on the old one again. Turning around and heading South again allowed us to sample the whole 18km expressway. Impressions? Its nice. Very smooth, very flowing and very fast. That said there are already some surface repairs in places, and something about the road surface and my high-end SuperCat tires meant that I had an annoying rattle whilst driving on the new road. A strange resonance or something. I do hope to see the speed limit increased on the expressway at some point; its very easy to speed as its so open and wide, and its a prime candidate for a trial of 110kph. It’s nice to see the work they put into the area surrounding the expressway too. Lots of green; new plantings and what will eventually be mounds of grass and bush. You can catch glimpses of the wetlands they build in various spots as well; just little ponds of water here and there. Anyway, back to what is important here. The Rover ran faultlessly the whole time, and was great to drive. It’s equally at home puttering around town, as it is at passing cars up hills and cruising the motorways. We made a quick stop for a rest, and take a couple of photos. Shes filthy, but in a well-loved kind of way. Unfortunately though, it doesn’t run on hopes and dreams, so a stop at the local Dino station was on the cards. What a surprise that was though! Yup, a drop of 2.2l/100km down to 15.9l/100km. Not bad for an old beast tuned by me. I have clocked just under 1200km since getting her, most of those done with the Speeduino setup. It’s good to see the economy finally working out, and becoming somewhat reasonable. I love driving this car, so will be using it as much as possible, as long as the weather holds out. Oh what I would do to have a carport or garage, instead of a car cover. More to come. Might FINALLY get around to doing the front speakers at some point, and it’ll need another warrant next month, so there is that to look forward to. Yay.

Just a small update We have Low thanks to 2" lowering springs up front and 2"blocks in the rear.

Small update. Massive thanks to old man KY for sending up a camshaft (thats not in two bits). Whacked that in and chucked the belt back on, engine turns over by hand with no odd noises or oddities (such as sudden loss in compression) which is a good start. I was hoping to compression test it but turns out its not really practical to do out of the car (cant bolt up starter etc without bell housing). Although might see if I can find a rb bellhousing for a loan as it will likely bolt up. Recent trip to Japan sourced a few goodies (crystal shifter, lace seat covers, stickers etc), and got my pine back on for some nice wheels so spent last night browsing yahoo japan. Also found a mooneyes visor haha https://wing-auctions.c.yimg.jp/sim?furl=auctions.c.yimg.jp/images.auctions.yahoo.co.jp/image/dr000/auc0212/users/7/0/8/5/mackys_1-img383x263-14818565326td6al22809.jpg&dc=1&sr.fs=20000 Need wof for nats so thats the primary goal (booked in for next weekend). Have done some work already that needed sorting so shoudl be straight forward.